A large tx latency issue was discovered during testing when only QBV was
enabled. The issue occurs because gtxoffset was not set when QBV is
active, it was only set when launch time is active.
The patch "igc: Correct the launchtime offset" only sets gtxoffset when
the launchtime_enable field is set by the user. Enabling launchtime_enable
ultimately sets the register IGC_TXQCTL_QUEUE_MODE_LAUNCHT (referred to as
LaunchT in the SW user manual).
Section 7.5.2.6 of the IGC i225/6 SW User Manual Rev 1.2.4 states:
"The latency between transmission scheduling (launch time) and the
time the packet is transmitted to the network is listed in Table 7-61."
However, the patch misinterprets the phrase "launch time" in that section
by assuming it specifically refers to the LaunchT register, whereas it
actually denotes the generic term for when a packet is released from the
internal buffer to the MAC transmit logic.
This launch time, as per that section, also implicitly refers to the QBV
gate open time, where a packet waits in the buffer for the QBV gate to
open. Therefore, latency applies whenever QBV is in use. TSN features such
as QBU and QAV reuse QBV, making the latency universal to TSN features.
Discussed with i226 HW owner (Shalev, Avi) and we were in agreement that
the term "launch time" used in Section 7.5.2.6 is not clear and can be
easily misinterpreted. Avi will update this section to:
"When TQAVCTRL.TRANSMIT_MODE = TSN, the latency between transmission
scheduling and the time the packet is transmitted to the network is listed
in Table 7-61."
Fix this issue by using igc_tsn_is_tx_mode_in_tsn() as a condition to
write to gtxoffset, aligning with the newly updated SW User Manual.
Tested:
1. Enrol taprio on talker board
base-time 0
cycle-time 1000000
flags 0x2
index 0 cmd S gatemask 0x1 interval1
index 0 cmd S gatemask 0x1 interval2
Note:
interval1 = interval for a 64 bytes packet to go through
interval2 = cycle-time - interval1
2. Take tcpdump on listener board
3. Use udp tai app on talker to send packets to listener
4. Check the timestamp on listener via wireshark
Test Result:
100 Mbps: 113 ~193 ns
1000 Mbps: 52 ~ 84 ns
2500 Mbps: 95 ~ 223 ns
Note that the test result is similar to the patch "igc: Correct the
launchtime offset".
Fixes: 790835fcc0cb ("igc: Correct the launchtime offset")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
remaining issues with the reset adapter logic in igc_tsn_offload_apply()
have been observed:
1. The reset adapter logics for i225 and i226 differ, although they should
be the same according to the guidelines in I225/6 HW Design Section
7.5.2.1 on software initialization during tx mode changes.
2. The i225 resets adapter every time, even though tx mode doesn't change.
This occurs solely based on the condition igc_is_device_id_i225() when
calling schedule_work().
3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only
resets adapter for legacy->tsn tx mode transitions.
4. qbv_count introduced in the patch is actually not needed; in this
context, a non-zero value of qbv_count is used to indicate if tx mode
was unconditionally set to tsn in igc_tsn_enable_offload(). This could
be replaced by checking the existing register
IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit.
This patch resolves all issues and enters schedule_work() to reset the
adapter only when changing tx mode. It also removes reliance on qbv_count.
qbv_count field will be removed in a future patch.
Test ran:
1. Verify reset adapter behaviour in i225/6:
a) Enrol a new GCL
Reset adapter observed (tx mode change legacy->tsn)
b) Enrol a new GCL without deleting qdisc
No reset adapter observed (tx mode remain tsn->tsn)
c) Delete qdisc
Reset adapter observed (tx mode change tsn->legacy)
2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed"
to confirm it remains resolved.
Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When user issues these cmds:
1. Either a) or b)
a) mqprio with hardware offload disabled
b) taprio with txtime-assist feature enabled
2. etf
3. tc qdisc delete
4. taprio with base time in the past
At step 4, qbv_config_change_errors wrongly increased by 1.
Excerpt from IEEE 802.1Q-2018 8.6.9.3.1:
"If AdminBaseTime specifies a time in the past, and the current schedule
is running, then: Increment ConfigChangeError counter"
qbv_config_change_errors should only increase if base time is in the past
and no taprio is active. In user perspective, taprio was not active when
first triggered at step 4. However, i225/6 reuses qbv for etf, so qbv is
enabled with a dummy schedule at step 2 where it enters
igc_tsn_enable_offload() and qbv_count got incremented to 1. At step 4, it
enters igc_tsn_enable_offload() again, qbv_count is incremented to 2.
Because taprio is running, tc_setup_type is TC_SETUP_QDISC_ETF and
qbv_count > 1, qbv_config_change_errors value got incremented.
This issue happens due to reliance on qbv_count field where a non-zero
value indicates that taprio is running. But qbv_count increases
regardless if taprio is triggered by user or by other tsn feature. It does
not align with qbv_config_change_errors expectation where it is only
concerned with taprio triggered by user.
Fixing this by relocating the qbv_config_change_errors logic to
igc_save_qbv_schedule(), eliminating reliance on qbv_count and its
inaccuracies from i225/6's multiple uses of qbv feature for other TSN
features.
The new function created: igc_tsn_is_taprio_activated_by_user() uses
taprio_offload_enable field to indicate that the current running taprio
was triggered by user, instead of triggered by non-qbv feature like etf.
Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Testing uncovered that even when the taprio gate is closed, some packets
still transmit.
According to i225/6 hardware errata [1], traffic might overflow the
planned QBV window. This happens because MAC maintains an internal buffer,
primarily for supporting half duplex retries. Therefore, even when the
gate closes, residual MAC data in the buffer may still transmit.
To mitigate this for i226, reduce the MAC's internal buffer from 192 bytes
to the recommended 88 bytes by modifying the RETX_CTL register value.
This follows guidelines from:
[1] Ethernet Controller I225/I22 Spec Update Rev 2.1 Errata Item 9:
TSN: Packet Transmission Might Cross Qbv Window
[2] I225/6 SW User Manual Rev 1.2.4: Section 8.11.5 Retry Buffer Control
Note that the RETX_CTL register can't be used in TSN mode because half
duplex feature cannot coexist with TSN.
Test Steps:
1. Send taprio cmd to board A:
tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 4 \
map 3 2 1 0 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time 0 \
sched-entry S 0x07 500000 \
sched-entry S 0x0f 500000 \
flags 0x2 \
txtime-delay 0
Note that for TC3, gate should open for 500us and close for another
500us.
3. Take tcpdump log on Board B.
4. Send udp packets via UDP tai app from Board A to Board B.
5. Analyze tcpdump log via wireshark log on Board B. Ensure that the
total time from the first to the last packet received during one cycle
for TC3 does not exceed 500us.
Fixes: 43546211738e ("igc: Add new device ID's")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The wol variable in ksz_port_set_mac_address() is declared with random
data, but the code in ksz_get_wol call may not be executed so the
WAKE_MAGIC check may be invalid resulting in an error message when
setting a MAC address after starting the DSA driver.
Fixes: 3b454b6390c3 ("net: dsa: microchip: ksz9477: Add Wake on Magic Packet support")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240805235200.24982-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot hit a use-after-free[1] which is caused because the bridge doesn't
make sure that all previous garbage has been collected when removing a
port. What happens is:
CPU 1 CPU 2
start gc cycle remove port
acquire gc lock first
wait for lock
call br_multicasg_gc() directly
acquire lock now but free port
the port can be freed
while grp timers still
running
Make sure all previous gc cycles have finished by using flush_work before
freeing the port.
[1]
BUG: KASAN: slab-use-after-free in br_multicast_port_group_expired+0x4c0/0x550 net/bridge/br_multicast.c:861
Read of size 8 at addr ffff888071d6d000 by task syz.5.1232/9699
CPU: 1 PID: 9699 Comm: syz.5.1232 Not tainted 6.10.0-rc5-syzkaller-00021-g24ca36a562d6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/07/2024
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:114
print_address_description mm/kasan/report.c:377 [inline]
print_report+0xc3/0x620 mm/kasan/report.c:488
kasan_report+0xd9/0x110 mm/kasan/report.c:601
br_multicast_port_group_expired+0x4c0/0x550 net/bridge/br_multicast.c:861
call_timer_fn+0x1a3/0x610 kernel/time/timer.c:1792
expire_timers kernel/time/timer.c:1843 [inline]
__run_timers+0x74b/0xaf0 kernel/time/timer.c:2417
__run_timer_base kernel/time/timer.c:2428 [inline]
__run_timer_base kernel/time/timer.c:2421 [inline]
run_timer_base+0x111/0x190 kernel/time/timer.c:2437
Reported-by: syzbot+263426984509be19c9a0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=263426984509be19c9a0
Fixes: e12cec65b554 ("net: bridge: mcast: destroy all entries via gc")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20240802080730.3206303-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Free the unused skb when not ip packets arrive.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heng Qi says:
====================
virtio-net: unbreak vq resizing if vq coalescing is not supported
Currently, if the driver does not negotiate the vq coalescing feature
but supports vq resize, the vq resize action, which could have been
successfully executed, is interrupted due to the failure in configuring
the vq coalescing parameters. This issue needs to be fixed.
Changelog
=========
v3->v4:
- Add a comment for patch[2/2].
v2->v3:
- Break out the feature check and the fix into separate patches.
v1->v2:
- Rephrase the subject.
- Put the feature check inside the virtnet_send_{r,t}x_ctrl_coal_vq_cmd.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't break the resize action if the vq coalescing feature
named VIRTIO_NET_F_VQ_NOTF_COAL is not negotiated.
Fixes: f61fe5f081cf ("virtio-net: fix the vq coalescing setting for vq resize")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Eugenio Pé rez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtio spec says:
The driver MUST have negotiated the VIRTIO_NET_F_VQ_NOTF_COAL
feature when issuing commands VIRTIO_NET_CTRL_NOTF_COAL_VQ_SET
and VIRTIO_NET_CTRL_NOTF_COAL_VQ_GET.
So we add the feature negotiation check to
virtnet_send_{r,t}x_ctrl_coal_vq_cmd as a basis for the next bugfix patch.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lifetime of TCP-AO static_key is the same as the last
tcp_ao_info. On the socket destruction tcp_ao_info ceases to be
with RCU grace period, while tcp-ao static branch is currently deferred
destructed. The static key definition is
: DEFINE_STATIC_KEY_DEFERRED_FALSE(tcp_ao_needed, HZ);
which means that if RCU grace period is delayed by more than a second
and tcp_ao_needed is in the process of disablement, other CPUs may
yet see tcp_ao_info which atent dead, but soon-to-be.
And that breaks the assumption of static_key_fast_inc_not_disabled().
See the comment near the definition:
> * The caller must make sure that the static key can't get disabled while
> * in this function. It doesn't patch jump labels, only adds a user to
> * an already enabled static key.
Originally it was introduced in commit eb8c507296f6 ("jump_label:
Prevent key->enabled int overflow"), which is needed for the atomic
contexts, one of which would be the creation of a full socket from a
request socket. In that atomic context, it's known by the presence
of the key (md5/ao) that the static branch is already enabled.
So, the ref counter for that static branch is just incremented
instead of holding the proper mutex.
static_key_fast_inc_not_disabled() is just a helper for such usage
case. But it must not be used if the static branch could get disabled
in parallel as it's not protected by jump_label_mutex and as a result,
races with jump_label_update() implementation details.
Happened on netdev test-bot[1], so not a theoretical issue:
[] jump_label: Fatal kernel bug, unexpected op at tcp_inbound_hash+0x1a7/0x870 [ffffffffa8c4e9b7] (eb 50 0f 1f 44 != 66 90 0f 1f 00)) size:2 type:1
[] ------------[ cut here ]------------
[] kernel BUG at arch/x86/kernel/jump_label.c:73!
[] Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI
[] CPU: 3 PID: 243 Comm: kworker/3:3 Not tainted 6.10.0-virtme #1
[] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[] Workqueue: events jump_label_update_timeout
[] RIP: 0010:__jump_label_patch+0x2f6/0x350
...
[] Call Trace:
[] <TASK>
[] arch_jump_label_transform_queue+0x6c/0x110
[] __jump_label_update+0xef/0x350
[] __static_key_slow_dec_cpuslocked.part.0+0x3c/0x60
[] jump_label_update_timeout+0x2c/0x40
[] process_one_work+0xe3b/0x1670
[] worker_thread+0x587/0xce0
[] kthread+0x28a/0x350
[] ret_from_fork+0x31/0x70
[] ret_from_fork_asm+0x1a/0x30
[] </TASK>
[] Modules linked in: veth
[] ---[ end trace 0000000000000000 ]---
[] RIP: 0010:__jump_label_patch+0x2f6/0x350
[1]: https://netdev-3.bots.linux.dev/vmksft-tcp-ao-dbg/results/696681/5-connect-deny-ipv6/stderr
Cc: stable@kernel.org
Fixes: 67fa83f7c86a ("net/tcp: Add static_key for TCP-AO")
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GVE driver wrongly relies on netif_carrier_ok() to check the
interface administrative state when resources are being
allocated/deallocated for queue(s). netif_carrier_ok() needs
to be replaced with netif_running() for all such cases.
Administrative state is the result of "ip link set dev <dev>
up/down". It reflects whether the administrator wants to use
the device for traffic and the corresponding resources have
been allocated.
Fixes: 5f08cd3d6423 ("gve: Alloc before freeing when adjusting queues")
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Shailend Chand <shailend@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240801205619.987396-1-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DEVID register contains two pieces of information: the device ID in
the upper nibble, and the silicon revision number in the lower nibble.
The driver should work fine with any silicon revision, so let's mask
that out in the device ID check.
Fixes: 20e6d190ffe1 ("net: pse-pd: Add TI TPS23881 PSE controller driver")
Signed-off-by: Kyle Swenson <kyle.swenson@est.tech>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20240731154152.4020668-1-kyle.swenson@est.tech
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot reported a null-ptr-deref while accessing sk2->sk_reuseport_cb in
reuseport_add_sock(). [0]
The repro first creates a listener with SO_REUSEPORT. Then, it creates
another listener on the same port and concurrently closes the first
listener.
The second listen() calls reuseport_add_sock() with the first listener as
sk2, where sk2->sk_reuseport_cb is not expected to be cleared concurrently,
but the close() does clear it by reuseport_detach_sock().
The problem is SCTP does not properly synchronise reuseport_alloc(),
reuseport_add_sock(), and reuseport_detach_sock().
The caller of reuseport_alloc() and reuseport_{add,detach}_sock() must
provide synchronisation for sockets that are classified into the same
reuseport group.
Otherwise, such sockets form multiple identical reuseport groups, and
all groups except one would be silently dead.
1. Two sockets call listen() concurrently
2. No socket in the same group found in sctp_ep_hashtable[]
3. Two sockets call reuseport_alloc() and form two reuseport groups
4. Only one group hit first in __sctp_rcv_lookup_endpoint() receives
incoming packets
Also, the reported null-ptr-deref could occur.
TCP/UDP guarantees that would not happen by holding the hash bucket lock.
Let's apply the locking strategy to __sctp_hash_endpoint() and
__sctp_unhash_endpoint().
[0]:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 1 UID: 0 PID: 10230 Comm: syz-executor119 Not tainted 6.10.0-syzkaller-12585-g301927d2d2eb #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/27/2024
RIP: 0010:reuseport_add_sock+0x27e/0x5e0 net/core/sock_reuseport.c:350
Code: 00 0f b7 5d 00 bf 01 00 00 00 89 de e8 1b a4 ff f7 83 fb 01 0f 85 a3 01 00 00 e8 6d a0 ff f7 49 8d 7e 12 48 89 f8 48 c1 e8 03 <42> 0f b6 04 28 84 c0 0f 85 4b 02 00 00 41 0f b7 5e 12 49 8d 7e 14
RSP: 0018:ffffc9000b947c98 EFLAGS: 00010202
RAX: 0000000000000002 RBX: ffff8880252ddf98 RCX: ffff888079478000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000012
RBP: 0000000000000001 R08: ffffffff8993e18d R09: 1ffffffff1fef385
R10: dffffc0000000000 R11: fffffbfff1fef386 R12: ffff8880252ddac0
R13: dffffc0000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 00007f24e45b96c0(0000) GS:ffff8880b9300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffcced5f7b8 CR3: 00000000241be000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__sctp_hash_endpoint net/sctp/input.c:762 [inline]
sctp_hash_endpoint+0x52a/0x600 net/sctp/input.c:790
sctp_listen_start net/sctp/socket.c:8570 [inline]
sctp_inet_listen+0x767/0xa20 net/sctp/socket.c:8625
__sys_listen_socket net/socket.c:1883 [inline]
__sys_listen+0x1b7/0x230 net/socket.c:1894
__do_sys_listen net/socket.c:1902 [inline]
__se_sys_listen net/socket.c:1900 [inline]
__x64_sys_listen+0x5a/0x70 net/socket.c:1900
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f24e46039b9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 91 1a 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f24e45b9228 EFLAGS: 00000246 ORIG_RAX: 0000000000000032
RAX: ffffffffffffffda RBX: 00007f24e468e428 RCX: 00007f24e46039b9
RDX: 00007f24e46039b9 RSI: 0000000000000003 RDI: 0000000000000004
RBP: 00007f24e468e420 R08: 00007f24e45b96c0 R09: 00007f24e45b96c0
R10: 00007f24e45b96c0 R11: 0000000000000246 R12: 00007f24e468e42c
R13: 00007f24e465a5dc R14: 0020000000000001 R15: 00007ffcced5f7d8
</TASK>
Modules linked in:
Fixes: 6ba845740267 ("sctp: process sk_reuseport in sctp_get_port_local")
Reported-by: syzbot+e6979a5d2f10ecb700e4@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=e6979a5d2f10ecb700e4
Tested-by: syzbot+e6979a5d2f10ecb700e4@syzkaller.appspotmail.com
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20240731234624.94055-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The old SysKonnect NIc's are not used or actively maintained anymore.
My sky2 NIC's are all in box in back corner of attic.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://patch.msgid.link/20240801162930.212299-1-stephen@networkplumber.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: fix endpoints with 'signal' and 'subflow' flags
When looking at improving the user experience around the MPTCP endpoints
setup, I noticed that setting an endpoint with both the 'signal' and the
'subflow' flags -- as it has been done in the past by users according to
bug reports we got -- was resulting on only announcing the endpoint, but
not using it to create subflows: the 'subflow' flag was then ignored.
My initial thought was to modify IPRoute2 to warn the user when the two
flags were set, but it doesn't sound normal to ignore one of them. I
then looked at modifying the kernel not to allow having the two flags
set, but when discussing about that with Mat, we thought it was maybe
not ideal to do that, as there might be use-cases, we might break some
configs. Then I saw it was working before v5.17. So instead, I fixed the
support on the kernel side (patch 5) using Paolo's suggestion. This also
includes a fix on the options side (patch 1: for v5.11+), an explicit
deny of some options combinations (patch 2: for v5.18+), and some
refactoring (patches 3 and 4) to ease the inclusion of the patch 5.
While at it, I added a new selftest (patch 7) to validate this case --
including a modification of the chk_add_nr helper to inverse the sides
were the counters are checked (patch 6) -- and allowed ADD_ADDR echo
just after the MP_JOIN 3WHS.
The selftests modification have the same Fixes tag as the previous
commit, but no 'Cc: Stable': if the backport can work, that's good --
but it still need to be verified by running the selftests -- if not, no
need to worry, many CIs will use the selftests from the last stable
version to validate previous stable releases.
====================
Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-0-c8a9b036493b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be quite uncommon to set both the subflow and the signal
flags: the initiator of the connection is typically the one creating new
subflows, not the other peer, then no need to announce additional local
addresses, and use it to create subflows.
But some people might be confused about the flags, and set both "just to
be sure at least the right one is set". To verify the previous fix, and
avoid future regressions, this specific case is now validated: the
client announces a new address, and initiates a new subflow from the
same address.
While working on this, another bug has been noticed, where the client
reset the new subflow because an ADD_ADDR echo got received as the 3rd
ACK: this new test also explicitly checks that no RST have been sent by
the client and server.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: 86e39e04482b ("mptcp: keep track of local endpoint still available for each msk")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-7-c8a9b036493b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the following commit, the client will initiate the ADD_ADDR, instead
of the server. We need to way to verify the ADD_ADDR have been correctly
sent.
Note: the default expected counters for when the port number is given
are never changed by the caller, no need to accept them as parameter
then.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: 86e39e04482b ("mptcp: keep track of local endpoint still available for each msk")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-6-c8a9b036493b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Up to the 'Fixes' commit, having an endpoint with both the 'signal' and
'subflow' flags, resulted in the creation of a subflow and an address
announcement using the address linked to this endpoint. After this
commit, only the address announcement was done, ignoring the 'subflow'
flag.
That's because the same bitmap is used for the two flags. It is OK to
keep this single bitmap, the already selected local endpoint simply have
to be re-used, but not via select_local_address() not to look at the
just modified bitmap.
Note that it is unusual to set the two flags together: creating a new
subflow using a new local address will implicitly advertise it to the
other peer. So in theory, no need to advertise it explicitly as well.
Maybe there are use-cases -- the subflow might not reach the other peer
that way, we can ask the other peer to try initiating the new subflow
without delay -- or very likely the user is confused, and put both flags
"just to be sure at least the right one is set". Still, if it is
allowed, the kernel should do what has been asked: using this endpoint
to announce the address and to create a new subflow from it.
An alternative is to forbid the use of the two flags together, but
that's probably too late, there are maybe use-cases, and it was working
before. This patch will avoid people complaining subflows are not
created using the endpoint they added with the 'subflow' and 'signal'
flag.
Note that with the current patch, the subflow might not be created in
some corner cases, e.g. if the 'subflows' limit was reached when sending
the ADD_ADDR, but changed later on. It is probably not worth splitting
id_avail_bitmap per target ('signal', 'subflow'), which will add another
large field to the msk "just" to track (again) endpoints. Anyway,
currently when the limits are changed, the kernel doesn't check if new
subflows can be created or removed, because we would need to keep track
of the received ADD_ADDR, and more. It sounds OK to assume that the
limits should be properly configured before establishing new
connections.
Fixes: 86e39e04482b ("mptcp: keep track of local endpoint still available for each msk")
Cc: stable@vger.kernel.org
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-5-c8a9b036493b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It sounds better to avoid wasting cycles and / or put extreme memory
pressure on the system by trying to create new subflows if it was not
possible to add a new item in the announce list.
While at it, a warning is now printed if the entry was already in the
list as it should not happen with the in-kernel path-manager. With this
PM, mptcp_pm_alloc_anno_list() should only fail in case of memory
pressure.
Fixes: b6c08380860b ("mptcp: remove addr and subflow in PM netlink")
Cc: stable@vger.kernel.org
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-4-c8a9b036493b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in the 'Fixes' commit, the port flag is only supported by
the 'signal' flag, and not by the 'subflow' one. Then if both the
'signal' and 'subflow' flags are set, the problem is the same: the
feature cannot work with the 'subflow' flag.
Technically, if both the 'signal' and 'subflow' flags are set, it will
be possible to create the listening socket, but not to establish a
subflow using this source port. So better to explicitly deny it, not to
create some confusions because the expected behaviour is not possible.
Fixes: 09f12c3ab7a5 ("mptcp: allow to use port and non-signal in set_flags")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-2-c8a9b036493b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before this patch, receiving an ADD_ADDR echo on the just connected
MP_JOIN subflow -- initiator side, after the MP_JOIN 3WHS -- was
resulting in an MP_RESET. That's because only ACKs with a DSS or
ADD_ADDRs without the echo bit were allowed.
Not allowing the ADD_ADDR echo after an MP_CAPABLE 3WHS makes sense, as
we are not supposed to send an ADD_ADDR before because it requires to be
in full established mode first. For the MP_JOIN 3WHS, that's different:
the ADD_ADDR can be sent on a previous subflow, and the ADD_ADDR echo
can be received on the recently created one. The other peer will already
be in fully established, so it is allowed to send that.
We can then relax the conditions here to accept the ADD_ADDR echo for
MPJ subflows.
Fixes: 67b12f792d5e ("mptcp: full fully established support after ADD_ADDR")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-1-c8a9b036493b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- core: drop bad gso csum_start and offset in virtio_net_hdr
- wifi: mt76: fix null pointer access in mt792x_mac_link_bss_remove
- eth: tun: add missing bpf_net_ctx_clear() in do_xdp_generic()
- phy: aquantia: only poll GLOBAL_CFG regs on aqr113, aqr113c and aqr115c
Current release - new code bugs:
- smc: prevent UAF in inet_create()
- bluetooth: btmtk: fix kernel crash when entering btmtk_usb_suspend
- eth: bnxt: reject unsupported hash functions
Previous releases - regressions:
- sched: act_ct: take care of padding in struct zones_ht_key
- netfilter: fix null-ptr-deref in iptable_nat_table_init().
- tcp: adjust clamping window for applications specifying SO_RCVBUF
Previous releases - always broken:
- ethtool: rss: small fixes to spec and GET
- mptcp:
- fix signal endpoint re-add
- pm: fix backup support in signal endpoints
- wifi: ath12k: fix soft lockup on suspend
- eth: bnxt_en: fix RSS logic in __bnxt_reserve_rings()
- eth: ice: fix AF_XDP ZC timeout and concurrency issues
- eth: mlx5:
- fix missing lock on sync reset reload
- fix error handling in irq_pool_request_irq
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=z53B
-----END PGP SIGNATURE-----
Merge tag 'net-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from wireless, bleutooth, BPF and netfilter.
Current release - regressions:
- core: drop bad gso csum_start and offset in virtio_net_hdr
- wifi: mt76: fix null pointer access in mt792x_mac_link_bss_remove
- eth: tun: add missing bpf_net_ctx_clear() in do_xdp_generic()
- phy: aquantia: only poll GLOBAL_CFG regs on aqr113, aqr113c and
aqr115c
Current release - new code bugs:
- smc: prevent UAF in inet_create()
- bluetooth: btmtk: fix kernel crash when entering btmtk_usb_suspend
- eth: bnxt: reject unsupported hash functions
Previous releases - regressions:
- sched: act_ct: take care of padding in struct zones_ht_key
- netfilter: fix null-ptr-deref in iptable_nat_table_init().
- tcp: adjust clamping window for applications specifying SO_RCVBUF
Previous releases - always broken:
- ethtool: rss: small fixes to spec and GET
- mptcp:
- fix signal endpoint re-add
- pm: fix backup support in signal endpoints
- wifi: ath12k: fix soft lockup on suspend
- eth: bnxt_en: fix RSS logic in __bnxt_reserve_rings()
- eth: ice: fix AF_XDP ZC timeout and concurrency issues
- eth: mlx5:
- fix missing lock on sync reset reload
- fix error handling in irq_pool_request_irq"
* tag 'net-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
mptcp: fix duplicate data handling
mptcp: fix bad RCVPRUNED mib accounting
ipv6: fix ndisc_is_useropt() handling for PIO
igc: Fix double reset adapter triggered from a single taprio cmd
net: MAINTAINERS: Demote Qualcomm IPA to "maintained"
net: wan: fsl_qmc_hdlc: Discard received CRC
net: wan: fsl_qmc_hdlc: Convert carrier_lock spinlock to a mutex
net/mlx5e: Add a check for the return value from mlx5_port_set_eth_ptys
net/mlx5e: Fix CT entry update leaks of modify header context
net/mlx5e: Require mlx5 tc classifier action support for IPsec prio capability
net/mlx5: Fix missing lock on sync reset reload
net/mlx5: Lag, don't use the hardcoded value of the first port
net/mlx5: DR, Fix 'stack guard page was hit' error in dr_rule
net/mlx5: Fix error handling in irq_pool_request_irq
net/mlx5: Always drain health in shutdown callback
net: Add skbuff.h to MAINTAINERS
r8169: don't increment tx_dropped in case of NETDEV_TX_BUSY
netfilter: iptables: Fix potential null-ptr-deref in ip6table_nat_table_init().
netfilter: iptables: Fix null-ptr-deref in iptable_nat_table_init().
net: drop bad gso csum_start and offset in virtio_net_hdr
...
Matthieu Baerts says:
====================
mptcp: fix duplicate data handling
In some cases, the subflow-level's copied_seq counter was incorrectly
increased, leading to an unexpected subflow reset.
Patch 1/2 fixes the RCVPRUNED MIB counter that was attached to the wrong
event since its introduction in v5.14, backported to v5.11.
Patch 2/2 fixes the copied_seq counter issues, is present since v5.10.
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
====================
Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-dup-data-v1-0-bde833fa628a@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a subflow receives and discards duplicate data, the mptcp
stack assumes that the consumed offset inside the current skb is
zero.
With multiple subflows receiving data simultaneously such assertion
does not held true. As a result the subflow-level copied_seq will
be incorrectly increased and later on the same subflow will observe
a bad mapping, leading to subflow reset.
Address the issue taking into account the skb consumed offset in
mptcp_subflow_discard_data().
Fixes: 04e4cd4f7ca4 ("mptcp: cleanup mptcp_subflow_discard_data()")
Cc: stable@vger.kernel.org
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/501
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since its introduction, the mentioned MIB accounted for the wrong
event: wake-up being skipped as not-needed on some edge condition
instead of incoming skb being dropped after landing in the (subflow)
receive queue.
Move the increment in the correct location.
Fixes: ce599c516386 ("mptcp: properly account bulk freed memory")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=dTVS
-----END PGP SIGNATURE-----
Merge tag 'nf-24-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Fix a possible null-ptr-deref sometimes triggered by iptables-restore at
boot time. Register iptables {ipv4,ipv6} nat table pernet in first place
to fix this issue. Patch #1 and #2 from Kuniyuki Iwashima.
netfilter pull request 24-07-31
* tag 'nf-24-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: iptables: Fix potential null-ptr-deref in ip6table_nat_table_init().
netfilter: iptables: Fix null-ptr-deref in iptable_nat_table_init().
====================
Link: https://patch.msgid.link/20240731213046.6194-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The current logic only works if the PIO is between two
other ND user options. This fixes it so that the PIO
can also be either before or after other ND user options
(for example the first or last option in the RA).
side note: there's actually Android tests verifying
a portion of the old broken behaviour, so:
https://android-review.googlesource.com/c/kernel/tests/+/3196704
fixes those up.
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Patrick Rohr <prohr@google.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: 048c796beb6e ("ipv6: adjust ndisc_is_useropt() to also return true for PIO")
Link: https://patch.msgid.link/20240730001748.147636-1-maze@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Following the implementation of "igc: Add TransmissionOverrun counter"
patch, when a taprio command is triggered by user, igc processes two
commands: TAPRIO_CMD_REPLACE followed by TAPRIO_CMD_STATS. However, both
commands unconditionally pass through igc_tsn_offload_apply() which
evaluates and triggers reset adapter. The double reset causes issues in
the calculation of adapter->qbv_count in igc.
TAPRIO_CMD_REPLACE command is expected to reset the adapter since it
activates qbv. It's unexpected for TAPRIO_CMD_STATS to do the same
because it doesn't configure any driver-specific TSN settings. So, the
evaluation in igc_tsn_offload_apply() isn't needed for TAPRIO_CMD_STATS.
To address this, commands parsing are relocated to
igc_tsn_enable_qbv_scheduling(). Commands that don't require an adapter
reset will exit after processing, thus avoiding igc_tsn_offload_apply().
Fixes: d3750076d464 ("igc: Add TransmissionOverrun counter")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240730173304.865479-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To the best of my knowledge, Alex Elder is not being paid to support
Qualcomm IPA networking drivers, so drop the status from "supported" to
"maintained".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alex Elder <elder@kernel.org>
Link: https://patch.msgid.link/20240730104016.22103-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Received frame from QMC contains the CRC.
Upper layers don't need this CRC and tcpdump mentioned trailing junk
data due to this CRC presence.
As some other HDLC driver, simply discard this CRC.
Fixes: d0f2258e79fd ("net: wan: Add support for QMC HDLC")
Cc: stable@vger.kernel.org
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240730063133.179598-1-herve.codina@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The carrier_lock spinlock protects the carrier detection. While it is
held, framer_get_status() is called which in turn takes a mutex.
This is not correct and can lead to a deadlock.
A run with PROVE_LOCKING enabled detected the issue:
[ BUG: Invalid wait context ]
...
c204ddbc (&framer->mutex){+.+.}-{3:3}, at: framer_get_status+0x40/0x78
other info that might help us debug this:
context-{4:4}
2 locks held by ifconfig/146:
#0: c0926a38 (rtnl_mutex){+.+.}-{3:3}, at: devinet_ioctl+0x12c/0x664
#1: c2006a40 (&qmc_hdlc->carrier_lock){....}-{2:2}, at: qmc_hdlc_framer_set_carrier+0x30/0x98
Avoid the spinlock usage and convert carrier_lock to a mutex.
Fixes: 54762918ca85 ("net: wan: fsl_qmc_hdlc: Add framer support")
Cc: stable@vger.kernel.org
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240730063104.179553-1-herve.codina@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan says:
====================
mlx5 misc fixes 2024-07-30
This patchset provides misc bug fixes from the team to the mlx5 core and
Eth drivers.
====================
Link: https://patch.msgid.link/20240730061638.1831002-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the documentation for mlx5_toggle_port_link states that it should
only be used after setting the port register, we add a check for the
return value from mlx5_port_set_eth_ptys to ensure the register was
successfully set before calling it.
Fixes: 667daedaecd1 ("net/mlx5e: Toggle link only after modifying port parameters")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-9-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit allocates a new modify header to replace the old
one when updating CT entry. But if failed to allocate a new one, eg.
exceed the max number firmware can support, modify header will be
an error pointer that will trigger a panic when deallocating it. And
the old modify header point is copied to old attr. When the old
attr is freed, the old modify header is lost.
Fix it by restoring the old attr to attr when failed to allocate a
new modify header context. So when the CT entry is freed, the right
modify header context will be freed. And the panic of accessing
error pointer is also fixed.
Fixes: 94ceffb48eac ("net/mlx5e: Implement CT entry update")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-8-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Require mlx5 classifier action support when creating IPSec chains in
offload path. MLX5_IPSEC_CAP_PRIO should only be set if CONFIG_MLX5_CLS_ACT
is enabled. If CONFIG_MLX5_CLS_ACT=n and MLX5_IPSEC_CAP_PRIO is set,
configuring IPsec offload will fail due to the mlxx5 ipsec chain rules
failing to be created due to lack of classifier action support.
Fixes: fa5aa2f89073 ("net/mlx5e: Use chains for IPsec policy priority offload")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit didn't change the body of the loop as it should.
It shouldn't be using MLX5_LAG_P1.
Fixes: 7e978e7714d6 ("net/mlx5: Lag, use actual number of lag ports")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch reduces the size of hw_ste_arr_optimized array that is
allocated on stack from 640 bytes (5 match STEs + 5 action STES)
to 448 bytes (2 match STEs + 5 action STES).
This fixes the 'stack guard page was hit' issue, while still fitting
majority of the usecases (up to 2 match STEs).
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case mlx5_irq_alloc fails, the previously allocated index remains
in the XArray, which could lead to inconsistencies.
Fix it by adding error handling that erases the allocated index
from the XArray if mlx5_irq_alloc returns an error.
Fixes: c36326d38d93 ("net/mlx5: Round-Robin EQs over IRQs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no point in recovery during device shutdown. if health
work started need to wait for it to avoid races and NULL pointer
access.
Hence, drain health WQ on shutdown callback.
Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver")
Fixes: d2aa060d40fa ("net/mlx5: Cancel health poll before sending panic teardown command")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The network maintainers need to be copied if the skbuff.h is touched.
This also helps git-send-email to figure out the proper maintainers when
touching the file.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240730161404.2028175-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The skb isn't consumed in case of NETDEV_TX_BUSY, therefore don't
increment the tx_dropped counter.
Fixes: 188f4af04618 ("r8169: use NETDEV_TX_{BUSY/OK}")
Cc: stable@vger.kernel.org
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/bbba9c48-8bac-4932-9aa1-d2ed63bc9433@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZqohDAAKCRDbK58LschI
g77FAQC4073GlQovH1d0owAjEbTllWAiZo7WYp/qY8GcJO5GqAEAyuefutwMQA8Z
7WxoXVrnOGxAGg/HzXJmY/w0GCaVRg8=
=nVz5
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-07-31
We've added 2 non-merge commits during the last 2 day(s) which contain
a total of 2 files changed, 2 insertions(+), 2 deletions(-).
The main changes are:
1) Fix BPF selftest build after tree sync with regards to a _GNU_SOURCE
macro redefined compilation error, from Stanislav Fomichev.
2) Fix a wrong test in the ASSERT_OK() check in uprobe_syscall BPF selftest,
from Jiri Olsa.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf/selftests: Fix ASSERT_OK condition check in uprobe_syscall test
selftests/bpf: Filter out _GNU_SOURCE when compiling test_cpp
====================
Link: https://patch.msgid.link/20240731115706.19677-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ip6table_nat_table_init() accesses net->gen->ptr[ip6table_nat_net_ops.id],
but the function is exposed to user space before the entry is allocated
via register_pernet_subsys().
Let's call register_pernet_subsys() before xt_register_template().
Fixes: fdacd57c79b7 ("netfilter: x_tables: never register tables by default")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David Laight pointed out that we should deal with the min3() and max3()
mess too, which still does excessive expansion.
And our current macros are actually rather broken.
In particular, the macros did this:
#define min3(x, y, z) min((typeof(x))min(x, y), z)
#define max3(x, y, z) max((typeof(x))max(x, y), z)
and that not only is a nested expansion of possibly very complex
arguments with all that involves, the typing with that "typeof()" cast
is completely wrong.
For example, imagine what happens in max3() if 'x' happens to be a
'unsigned char', but 'y' and 'z' are 'unsigned long'. The types are
compatible, and there's no warning - but the result is just random
garbage.
No, I don't think we've ever hit that issue in practice, but since we
now have sane infrastructure for doing this right, let's just use it.
It fixes any excessive expansion, and also avoids these kinds of broken
type issues.
Requested-by: David Laight <David.Laight@aculab.com>
Acked-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
