On my test platform (B2020/STiH416) the serial port issues bad characters
during the initial message avalanche as the console comes up. The problem
also occurs when dense(ish) I/O is done using the polled I/O interface.
The problem is fixed for me by using the FIFO half-empty bit rather than
FIFO full bit. Note that using the half-empty bit causes the FIFO to be
managed in a similar way to interrupt based I/O (i.e. where the hardware
gets best test coverage).
Running the FIFO half full will have no impact (good or bad) on console
performance. The UART will still remain fully saturated and the busy-wait
until the FIFO is empty in asc_console_write() will complete at the same
time.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xilinx MDM (Microblaze Debug Module) also contains
uart interface via JTAG which is compatible with
uartlite driver. This interface is really slow
that's why timeout is setup to 1s.
Make this time delay not to be cpu speed dependent.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `lpuart_dma_rx_free':
fsl_lpuart.c:(.text+0x7da28): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_tx_free':
fsl_lpuart.c:(.text+0x7da60): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_rx':
fsl_lpuart.c:(.text+0x7dab8): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_dma_tx':
fsl_lpuart.c:(.text+0x7db7e): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_copy_rx_to_tty':
fsl_lpuart.c:(.text+0x7dcd4): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb78b811422cd2d8c8605949cc4cc13618347ad5 provide a workaround for
kernel panic, but bring potential deadlock risk. that is in
sirfsoc_rx_tmo_process_tl while enter into sirfsoc_uart_pio_rx_chars
cpu hold uart_port->lock, if uart interrupt comes cpu enter into
sirfsoc_uart_isr and deadlock occurs in getting uart_port->lock.
the patch replace spin_lock version to spin_lock_irq* version to avoid
spinlock dead lock issue. let function tty_flip_buffer_push in tasklet
outof spin_lock_irq* protect area to avoid add the pair of spin_lock and
spin_unlock for tty_flip_buffer_push.
BTW drop self defined unused spinlock protect of tx_lock/rx_lock.
56274.220464] BUG: spinlock lockup suspected on CPU#0, swapper/0/0
[56274.223648] lock: 0xc05d9db0, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
[56274.231278] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G
O 3.10.35 #1
[56274.238241] [<c0015530>] (unwind_backtrace+0x0/0xf4) from
[<c00120d8>] (show_stack+0x10/0x14)
[56274.246742] [<c00120d8>] (show_stack+0x10/0x14) from
[<c01b11b0>] (do_raw_spin_lock+0x110/0x184)
[56274.255501] [<c01b11b0>] (do_raw_spin_lock+0x110/0x184) from
[<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c)
[56274.264874] [<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c) from
[<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
[56274.274758] [<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
from [<c00758f4>] (handle_irq_event+0x3c/0x5c)
[56274.284561] [<c00758f4>] (handle_irq_event+0x3c/0x5c) from
[<c0077fa0>] (handle_level_irq+0x98/0xfc)
[56274.293670] [<c0077fa0>] (handle_level_irq+0x98/0xfc) from
[<c0074f44>] (generic_handle_irq+0x2c/0x3c)
[56274.302952] [<c0074f44>] (generic_handle_irq+0x2c/0x3c) from
[<c000ef80>] (handle_IRQ+0x40/0x90)
[56274.311706] [<c000ef80>] (handle_IRQ+0x40/0x90) from
[<c000dc80>] (__irq_svc+0x40/0x70)
[56274.319697] [<c000dc80>] (__irq_svc+0x40/0x70) from
[<c038113c>] (_raw_spin_unlock_irqrestore+0x10/0x48)
[56274.329158] [<c038113c>]
(_raw_spin_unlock_irqrestore+0x10/0x48) from [<c0200034>]
(tty_port_tty_get+0x58/0x90)
[56274.339213] [<c0200034>] (tty_port_tty_get+0x58/0x90) from
[<c0212008>] (sirfsoc_uart_pio_rx_chars+0x1c/0xc8)
[56274.349097] [<c0212008>]
(sirfsoc_uart_pio_rx_chars+0x1c/0xc8) from [<c0212ef8>]
(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc)
[56274.359853] [<c0212ef8>]
(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc) from [<c0027c04>]
(tasklet_action+0x84/0x114)
[56274.369739] [<c0027c04>] (tasklet_action+0x84/0x114) from
[<c0027db4>] (__do_softirq+0x120/0x200)
[56274.378585] [<c0027db4>] (__do_softirq+0x120/0x200) from
[<c0027f44>] (do_softirq+0x54/0x5c)
[56274.386998] [<c0027f44>] (do_softirq+0x54/0x5c) from
[<c00281ec>] (irq_exit+0x9c/0xd0)
[56274.394899] [<c00281ec>] (irq_exit+0x9c/0xd0) from
[<c000ef84>] (handle_IRQ+0x44/0x90)
[56274.402790] [<c000ef84>] (handle_IRQ+0x44/0x90) from
[<c000dc80>] (__irq_svc+0x40/0x70)
[56274.410774] [<c000dc80>] (__irq_svc+0x40/0x70) from
[<c0288af4>] (cpuidle_enter_state+0x50/0xe0)
[56274.419532] [<c0288af4>] (cpuidle_enter_state+0x50/0xe0) from
[<c0288c34>] (cpuidle_idle_call+0xb0/0x148)
[56274.429080] [<c0288c34>] (cpuidle_idle_call+0xb0/0x148) from
[<c000f3ac>] (arch_cpu_idle+0x8/0x38)
[56274.438016] [<c000f3ac>] (arch_cpu_idle+0x8/0x38) from
[<c0059344>] (cpu_startup_entry+0xfc/0x140)
[56274.446956] [<c0059344>] (cpu_startup_entry+0xfc/0x140) from
[<c04a3a54>] (start_kernel+0x2d8/0x2e4)
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All SiRFSoC UART registers are in 32-bits. If we use writeb for
TXFIFO, actually all of 32-bits are still written, for TXTIFO,
only low 8-bits are valid, so in prima2&atlas6, this causes no
problem.
But in the new atlas7, using writeb to write UART registers will
cause an imprecise data abort as HW does check the "wrong" writeb.
So move to writel and this also makes the code consistent with
sirfsoc_uart_pio_tx_chars() in which we use writel.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two new drivers have been added since 3.14, the MEN 16z135 uart, and
the ARM semihosting console. Both are missing an explicit 'select
SERIAL_CORE', which can leads build errors when no other driver
selects the core, as found during ARM randconfig testing.
In case of the ARM semihosting console, we also have to select
SERIAL_CORE_CONSOLE.
This adds the missing 'select' statements.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the warnings:
drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_rx':
>> drivers/tty/serial/sc16is7xx.c:548:1: warning: 'sc16is7xx_handle_rx' uses dynamic stack allocation [enabled by default]
drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_tx':
>> drivers/tty/serial/sc16is7xx.c:589:1: warning: 'sc16is7xx_handle_tx' uses dynamic stack allocation [enabled by default]
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/sc16is7xx.c:1060:12: warning: 'sc16is7xx_probe' defined but not used [-Wunused-function]
static int sc16is7xx_probe(struct device *dev,
^
drivers/tty/serial/sc16is7xx.c:1176:12: warning: 'sc16is7xx_remove' defined but not used [-Wunused-function]
static int sc16is7xx_remove(struct device *dev)
^
drivers/tty/serial/sc16is7xx.c:1215:29: warning: 'regcfg' defined but not used [-Wunused-variable]
static struct regmap_config regcfg = {
^
Fixed these warnings by removing the `#ifdef CONFIG_REGMAP_I2C' around their
calls as this driver selects REGMAP_I2C in Kconfig. This part of driver just
didn't compile at all when REGMAP_I2C configured as module (CONFIG_REGMAP_I2C
is not defined, just CONFIG_REGMAP_I2C_MODULE).
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On initialization failure, an error message is already printed with
level KERN_ERR, no need to print another one with level KERN_INFO.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pch_uart driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is largely a duplicate of paste_selection() in
drivers/tty/vt/selection.c, but with its own selection state. The
speakup selection mechanism should really be merged with vt.
For now, apply the changes from 'TTY: vt, fix paste_selection ldisc
handling', 'tty: Make ldisc input flow control concurrency-friendly',
and 'tty: Fix unsafe vt paste_selection()'.
References: https://bugs.debian.org/735202
References: https://bugs.debian.org/744015
Reported-by: Paul Gevers <elbrus@debian.org>
Reported-and-tested-by: Jarek Czekalski <jarekczek@poczta.onet.pl>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org> # v3.8 but needs backporting for < 3.12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the conflicts in the files:
drivers/iio/adc/Kconfig
drivers/staging/rtl8723au/os_dep/usb_ops_linux.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable DT based earlycon initialization for the pl011 uart.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: Grant Likely <grant.likely@linaro.org>
This adds the infrastructure to generic earlycon for earlycon setup
using DT. The actual setup is not enabled until a following commit to
add the FDT parsing.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Likely <grant.likely@linaro.org>
No functional change. Just convert to the new interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Link: http://lkml.kernel.org/r/20140507154337.873477334@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No functional change. Just convert to the new interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Link: http://lkml.kernel.org/r/20140507154337.643399187@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mostly spacing changes, also making the operations structure const
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9aac5887595 (tty/serial: add generic serial earlycon) moved
console option parsing from 8250_early.c and converted to kstrto*
functions from simple_strtoul along the way. However, kstrto* functions
are not equivalent in that they do not allow non-convertible characters
at the end such as "115200n8". Fix this by changing back to
simple_strtoul and ignore what checkpatch.pl says.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d2fd6810a823bcd (tty/serial: convert 8250 to generic earlycon)
removed setup_early_serial8250_console, but there are still 2 callers
in:
arch/mips/mti-malta/malta-init.c
drivers/firmware/pcdp.c
Add back the function implemented as a wrapper to setup_earlycon.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6a20dbd6caa2358716136144bf524331d70b1e03,
"tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
correctly identifies an unsafe race condition between
__tty_buffer_request_room() and flush_to_ldisc(), where the consumer
flush_to_ldisc() prematurely advances the head before consuming the
last of the data committed. For example:
CPU 0 | CPU 1
__tty_buffer_request_room | flush_to_ldisc
... | ...
| count = head->commit - head->read
n = tty_buffer_alloc() |
b->commit = b->used |
b->next = n |
| if (!count) /* T */
| if (head->next == NULL) /* F */
| buf->head = head->next
In this case, buf->head has been advanced but head->commit may have
been updated with a new value.
Instead of reintroducing an unnecessary lock, fix the race locklessly.
Read the commit-next pair in the reverse order of writing, which guarantees
the commit value read is the latest value written if the head is
advancing.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6a20dbd6caa2358716136144bf524331d70b1e03.
Although the commit correctly identifies an unsafe race condition
between __tty_buffer_request_room() and flush_to_ldisc(), the commit
fixes the race with an unnecessary spinlock in a lockless algorithm.
The follow-on commit, "tty: Fix lockless tty buffer race" fixes
the race locklessly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 'console=hvc0' is specified to the kernel parameter in x86 KVM guest,
hvc console is setup within a kthread. However, that will cause SEGV
and the boot will fail when the driver is builtin to the kernel,
because currently hvc_console_setup() is annotated with '__init'. This
patch removes '__init' to boot the guest successfully with 'console=hvc0'.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty atomic_write_lock does not provide an exclusion guarantee for
the tty driver if the termios settings are LECHO & !OPOST. And since
it is unexpected and not allowed to call TTY buffer helpers like
tty_insert_flip_string concurrently, this may lead to crashes when
concurrect writers call pty_write. In that case the following two
writers:
* the ECHOing from a workqueue and
* pty_write from the process
race and can overflow the corresponding TTY buffer like follows.
If we look into tty_insert_flip_string_fixed_flag, there is:
int space = __tty_buffer_request_room(port, goal, flags);
struct tty_buffer *tb = port->buf.tail;
...
memcpy(char_buf_ptr(tb, tb->used), chars, space);
...
tb->used += space;
so the race of the two can result in something like this:
A B
__tty_buffer_request_room
__tty_buffer_request_room
memcpy(buf(tb->used), ...)
tb->used += space;
memcpy(buf(tb->used), ...) ->BOOM
B's memcpy is past the tty_buffer due to the previous A's tb->used
increment.
Since the N_TTY line discipline input processing can output
concurrently with a tty write, obtain the N_TTY ldisc output_lock to
serialize echo output with normal tty writes. This ensures the tty
buffer helper tty_insert_flip_string is not called concurrently and
everything is fine.
Note that this is nicely reproducible by an ordinary user using
forkpty and some setup around that (raw termios + ECHO). And it is
present in kernels at least after commit
d945cb9cce20ac7143c2de8d88b187f62db99bdc (pty: Rework the pty layer to
use the normal buffering logic) in 2.6.31-rc3.
js: add more info to the commit log
js: switch to bool
js: lock unconditionally
js: lock only the tty->ops->write call
References: CVE-2014-0196
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sleep function was updated to put the serial port to sleep only when necessary.
This appears to resolve the errant behavior of the driver as described in
Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not
work with 3.8.0".
Signed-off-by: Michael Welling <mwelling@ieee.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix by including linux/uaccess.h:
drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_ioctl':
>> drivers/tty/serial/sc16is7xx.c:861:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/sc16is7xx.c:867:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SC16IS7xx is a slave I2C-bus/SPI interface to a single-channel
high performance UART. The SC16IS7xx's internal register set is
backward-compatible with the widely used and widely popular 16C450.
The SC16IS7xx also provides additional advanced features such as
auto hardware and software flow control, automatic RS-485 support, and
software reset.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fcbee4d49f30eb0eaa83a62e6a3cab5a892ed93f.
It wasn't quite ready to go in yet, sorry about that.
Cc: Simon Horman <horms@verge.net.au>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add earlycon support for the arm/arm64 semihosting debug serial
interface. This allows enabling a debug console when early_params are
processed. This is based on the arm64 earlyprintk smh support and is
intended to replace it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add earlycon support for the pl011 serial port. This allows enabling
the pl011 for console when early_params are processed. This is based
on the arm64 earlyprintk support and is intended to replace it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the generic earlycon infrastructure in place, convert the 8250
early console to use it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This introduces generic earlycon infrastructure for serial devices
based on the 8250 earlycon. This allows for supporting earlycon option
with other serial devices. The earlycon output is enabled at the time
early_params are processed.
Only architectures that have fixmap support or have functional ioremap
when early_params are processed are supported. This is the same
restriction that the 8250 driver had.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to support FIX_EARLYCON_MEM on other arches, make the
option per arch.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver for MEN's 16z135 High Speed UART.
The 16z135 is a memory mapped UART Core on an MCB FPGA and has 1024 byte
deep FIFO buffers for the RX and TX path. It also has configurable FIFO
fill level IRQs and data copied to and from the hardware has to be
acknowledged.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zynq's UART is Cadence IP. Make this visible in the prompt in kconfig
and additional comments in the driver.
This also renames functions and symbols, as far as possible without
breaking user space API, to reflect the Cadence origin. This is achieved
through simple search and replace:
- s/XUARTPS/CDNS_UART/g
- s/xuartps/cdns_uart/g
The only exceptions are PORT_XUARTPS and the driver name, which stay as is,
due to their exposure to user space. As well as the - no legacy -
compatibility string 'xlnx,xuartps'
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A comment states, that, according to the data sheet, to enable
interrupts the disable register should be written, but the enable
register could be left untouched. And it suspsects a HW bug requiring
to write both.
Reviewing the data sheet, these statements seem wrong. Just as one would
expect. Writing to the enable/disable register enables/disables
interrupts.
Hence the misleading comment and needless write to the disable register
are removed from the enable sequence.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A lot of read-modify-write sequences used a one-line statement which
nests a readl() within a writel(). Convert this into code sequences that
make the three steps more obvious.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print a warning if the clock notifier rejects a clock frequency change
to facilitate debugging (see:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/304329/focus=304379)
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is all white space and comment clean up. Mostly reformatting
comments.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register port numbers according to order in DT aliases.
If aliases are not defined, order in DT is used.
If aliases are defined, register port id based
on that.
This patch ensures proper ttyPS0/1 assignment.
[soren]: Combined integer declarations in probe(), removed warning message
if no alias is found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nobody passes a DTR_gpio to this driver, so
this code is not necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
just using helper function to remove some duplicated
code a bit. While at that, also move allocation of
struct uart_omap_port higher in the code so that
we return much earlier in case of no memory.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this way we can remove one pointer declaration.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
