act8846_matches and act8865_matches are defined only when OF is
enabled. Move references to them to the act8865_pdata_from_dt()
function to avoid a build error when OF is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add device id and definition of registers and regulators to support
the act8846 PMU.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch prepares support for other devices in the act88xx family of
PMUs manufactured by Active-Semi.
http://www.active-semi.com/products/power-management-units/act88xx/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
act8865_pdata_from_dt() populates the array pdata->regulators with all
the regulators and then assigns the field init_data only for the ones
actually found in the DT.
The patch changes the value assigned to pdata->num_regulators to match
the size of the array.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simply use ret variable instead.
Also remove unneeded initialize for ret variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver loops through all available regulators (ACT8865_REG_NUM)
and accesses pdata->regulators[i].platform_data without checking the
actual value of num_regulators in platform data, potentially causing a
invalid memory access.
Fix this and look up the regulator init_data by id in platform data.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by Wenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Load switches are modeled as regulators but they just provide
the voltage of their parent input supply. So, the drivers for
these switches usually neither provide a .list_voltage handler
not set a .n_voltages count. But there is code in the kernel
that assumes that all regulators should be able to provide this
information (e.g: cpufreq and mmc subsystems).
If the voltage count and list are not available for a regulator
and it has a parent input supply, then use the parent values.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Load switches are modeled as regulators but they just provide
the voltage of their parent input supply. So the drivers for
these switches usually don't provide a .get_voltage function
handler but there is code in the kernel that assumes that all
regulators should be able to provide its current voltage rail.
So, if the output voltage for a regulator is not available and
it has a parent supply, then pass the voltage of its parent.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
The second range of this particular regulator,
starts at 1.60V, not as 1.55V as it was originally
implied by code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
act8865_pdata_from_dt() populates the array pdata->regulators with all
the regulators and then assigns the field init_data only for the ones
actually found in the DT.
The patch changes the value assigned to pdata->num_regulators to match
the size of the array.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
WM5110/8280 devices do not support bypass mode for LDO1 so remove
the bypass callbacks registered with regulator core.
Signed-off-by: Nikesh Oswal <nikesh@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Correct the the config register for LDO1.
Fixes: 90e7d5262796 (regulator: tps65218: Add Regulator driver for
TPS65218 PMIC)
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15
'name' field was re-initialized and getting overwritten in some
cases possibly due to a typo. Code inspection says the second time
it should be 'sname' instead of 'name'. Replace it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When setting up .enable_reg for an SMPS regulator, presumably we should
call PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE, ...) rather than using
LDO_BASE. This change makes the LCD panel and HDMI work again on the
NVIDIA Dalmore board anyway.
Fixes: 318dbb02b50c ("regulator: palmas: Fix SMPS enable/disable/is_enabled")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The vbus regulator was not getting its name set. This results
in the sysfs entry being empty. The lack of a bcm590xx_regs[]
table entry also upsets Coverity runs. Add the table entry
so the name gets set properly.
Signed-off-by: Graham Williams <graham.williams@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_REGULATOR_AB8500_DEBUG is always not defined.
ab8500_regulator_debug_init() is not called at all now,
ab8500_regulator_debug_exit() simply return 0, thus remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now this is a DT-only driver because non-devicetree probe path is removed,
so merge ab8500_regulator_of_probe() into ab8500_regulator_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.
Currently we do not populate these for SMPS other than SMPS10, this
results in spurious results as regmap assumes that the values are
valid and ends up reading register 0x0 RTC:SECONDS_REG on Palmas
variants that do have RTC! To fix this, we update proper parameters
for the descriptor fields.
Further, we want to ensure the behavior consistent with logic
prior to commit dbabd624d4eec50b6, where, once you do a set_mode,
enable/disable ensure the logic remains consistent and configures
Palmas to the configuration that we set with set_mode (since the
configuration register is common). To do this, we can rely on the
regulator core's regulator_register behavior where the regulator
descriptor pointer provided by the regulator driver is stored. (no
reallocation and copy is done). This lets us update the enable_value
post registration, to remain consistent with the mode we configure as
part of set_mode.
Fixes: dbabd624d4eec50b6 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name() walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
re-add the perm check (we unified the module param and sysfs checks, but
the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args().
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IxSN
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Most of this is cleaning up various driver sysfs permissions so we can
re-add the perm check (we unified the module param and sysfs checks,
but the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args()"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: set nx before marking module MODULE_STATE_COMING.
samples/kobject/: avoid world-writable sysfs files.
drivers/hid/hid-picolcd_fb: avoid world-writable sysfs files.
drivers/staging/speakup/: avoid world-writable sysfs files.
drivers/regulator/virtual: avoid world-writable sysfs files.
drivers/scsi/pm8001/pm8001_ctl.c: avoid world-writable sysfs files.
drivers/hid/hid-lg4ff.c: avoid world-writable sysfs files.
drivers/video/fbdev/sm501fb.c: avoid world-writable sysfs files.
drivers/mtd/devices/docg3.c: avoid world-writable sysfs files.
speakup: fix incorrect perms on speakup_acntsa.c
cpumask.h: silence warning with -Wsign-compare
Documentation: Update kernel-parameters.tx
param: hand arguments after -- straight to init
modpost: Fix resource leak in read_dump()
The PM800_BUCK3 define is cut and pasted twice so we can remove the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
get_voltage_sel reads from SMPS register - if the read selector value
is 0, the SMPS is actually disabled - So, this is in addition to the
ctrl_register that may also be used to enable/disable the SMPS.
The original logic(prior to commit dbabd624d4eec50b6) used to be:
static int palmas_map_voltage_smps(struct regulator_dev *rdev,
int min_uV, int max_uV)
<snip>
if (min_uV == 0)
return 0;
To handle this scenario, with the transition to regulator_list
implementation, we seem to have missed the data necessary to mark as
one of the valid entries as "0" 'disabled regulator' which results in
0 volts - So, stick with pre-existing logic.
Without this added to the list, palmas regulator driver,
on probe, attempts to setup constraints and in the case of
OMAP5uEVM, SMPS9 (which is mapped for 2v1 audio supply) fails in
regulator_list_voltage_linear_range mapping of '0', and as a fall back
of constraints not being applied, the entire regulator list is not
enumerated due to assumption that something system wide has gone bad
on with the PMIC.
Fixes: dbabd624d4eec50b6 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With commit 064d5cd110f94ce41ca5681dcda8b77fa63d5b95
(regulator: core: Fix the init of DT defined fixed regulators)
We ensure that regulator must be capable of providing it's current
voltage when constraints are used, however adding the return value in
the print is a little more informative to explain the nature of the
failure involved.
So, instead of providing message such as:
smps9: failed to get the current voltage
having error value added to the message such as:
smps9: failed to get the current voltage(-22)
is a little more informative for debugging the error.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- Move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- Fixes reference counting of the DT nodes for constraints from Charles
Keepax. This has little practical impact since all real users of
the regulator bindings use FDT which doesn't need the reference
counting.
- Lots of cleanups, especially to the Samsung drivers.
- Support for Linear Technologies LTC3589, Texas Instruments TPS658640
and X-Powers AXP20x.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JrfM
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into next
Pull regulator updates from Mark Brown:
"The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- fixes to reference counting of the DT nodes for constraints from
Charles Keepax. This has little practical impact since all real
users of the regulator bindings use FDT which doesn't need the
reference counting.
- lots of cleanups, especially to the Samsung drivers.
- support for Linear Technologies LTC3589, Texas Instruments
TPS658640 and X-Powers AXP20x"
* tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (64 commits)
regulator: pbias: remove unnecessary OOM messages
regulator: max8649: remove unnecessary OOM messages
regulator: core: Fix the init of DT defined fixed regulators
regulator: core: Disable unused regulators after deferred probing is done
regulator: Don't disable unused regulators we don't have permission for
regulator: axp20x: Use regulator_map_voltage_ascend for LDO4
regulator: use of_property_read_{bool|u32}()
regulator: Fix regulator_get_{optional,exclusive}() documentation
regulators: Add definition of regulator_set_voltage_time() for !CONFIG_REGULATOR
regulator: arizona-ldo1: add missing #include
regulator: pfuze100: Support enable/disable for fixed regulator
regulator: ltc3589: Remove ltc3589_list_voltage_fixed function
regulator: ltc3589: Fix module dependency
regulator: tps6586x: Remove unused to_tps6586x_dev() function
regulator: tps65218: Convert to use regulator_set_voltage_time_sel
regulator: tps6586x: Add support for the TPS658640
regulator: tps6586x: Prepare supporting fixed regulators
regulator: pfuze100: Don't allocate an invalid gpio
regulator: pfuze100: Support SWB enable/disable
regulator: fixed: use of_property_read_{bool|u32}()
...
As of commit 064d5cd110f9 (regulator: core: Fix the init of DT defined
fixed regulators) the regulator core tries to query the current voltage
of a regulator when applying constraints. This exposes a bug in the
AS3722 regulator driver which fails to read the voltage of disabled
regulators. The reason is that the hardware is programmed to a selector
of 0, but none of the voltage tables include 0 as a valid selector. The
datasheets indicate that 0 is a valid selector when the regulators are
powered off.
To fix this, add a range including selector 0 to the voltage tables.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here is the big char / misc driver updates for 3.16-rc1.
Lots of different driver updates for a variety of different drivers and
minor driver subsystems.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONWI8ACgkQMUfUDdst+ykvQACdGxTChdEU7edElDAXeelVmu8v
D1UAoLDvqwUsN7t5v+WG2wkOvhf5MEA7
=tVMP
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into next
Pull char/misc driver patches from Greg KH:
"Here is the big char / misc driver update for 3.16-rc1.
Lots of different driver updates for a variety of different drivers
and minor driver subsystems.
All have been in linux-next with no reported issues"
* tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (79 commits)
hv: use correct order when freeing monitor_pages
spmi: of: fixup generic SPMI devicetree binding example
applicom: dereferencing NULL on error path
misc: genwqe: fix uninitialized return value in genwqe_free_sync_sgl()
miscdevice.h: Simple syntax fix to make pointers consistent.
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
mcb: Add support for shared PCI IRQs
drivers: Remove duplicate conditionally included subdirs
misc: atmel_pwm: only build for supported platforms
mei: me: move probe quirk to cfg structure
mei: add per device configuration
mei: me: read H_CSR after asserting reset
mei: me: drop harmful wait optimization
mei: me: fix hw ready reset flow
mei: fix memory leak of mei_clients array
uio: fix vma io range check in mmap
drivers: uio_dmem_genirq: Fix memory leak in uio_dmem_genirq_probe()
w1: do not unlock unheld list_mutex in __w1_remove_master_device()
w1: optional bundling of netlink kernel replies
connector: allow multiple messages to be sent in one packet
...
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a regulator is defined using DT and it has a single voltage the
regulator init always tries to apply this voltage. However it fails if
the regulator isn't settable because it is using an internal low level
function. To overcome this we now first query the regulator and only
set it if needed.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_init_complete does a scan of regulators which dont have
always-on or consumers are automatically disabled as being unused.
However, with deferred probing, late_initcall() is too soon to
declare a regulator as unused as the regulator itself might not
have registered due to defferal - Example: A regulator deffered due
to i2bus not available which in turn is deffered due to pinctrl
availability.
Since deferred probing is done in late_initcall(), do the cleanup of
unused regulators by regulator_init_complete in late_initcall_sync
instead of late_initcall.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
[nm@ti.com: minor rewording]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the spirit of conservatism that governs our general approach to
permissions it is better if we don't touch regulators we weren't explicitly
given permissions to control. This avoids the need to explicitly specify
unknown regulators in DT as always on, if a regulator is not otherwise
involved in software control it can be omitted from the DT.
Regulators explicitly given constraints in DT still need to have an always
on constraint specified as before.
Signed-off-by: Mark Brown <broonie@linaro.org>
The voltages in axp20x_ldo4_data table are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use more compact of_property_read_{bool|u32}() calls instead of the
of_{find|get}_property() calls in of_get_regulation_constraints() where
possible (note that of_property_read_{bool|u32}() were already used to read
some properties).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_get_optional() doesn't hold an exclusive reference to
the regulator. Fix the documentation and reword the exclusive
documentation to fix the grammatical error "this reference is
held".
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
commit 2cce4be9e6b8 "regulator: arizona-ldo1: Add processing of init_data
from device tree" added a call to of_get_child_by_name() but
did not add an #include to the header file declaring that function.
I got a build error when doing randconfig testing on this, which
is fixed by this patch to include of.h.
drivers/regulator/arizona-ldo1.c:192:2: error: implicit declaration of function 'of_get_child_by_name' [-Werror=implicit-function-declaration]
drivers/regulator/arizona-ldo1.c:193:2: error: implicit declaration of function 'of_parse_phandle' [-Werror=implicit-function-declaration]
drivers/regulator/arizona-ldo1.c:213:2: error: implicit declaration of function 'of_node_put' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
