Setting QUEUE_FLAG_NOMERGES was added in commit 15dd03811d99dcf
("scsi: megaraid_sas: NVME Interface detection and prop settings")
without any explanation. Drivers should second guess the block
layer merge decisions, so remove the flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240627124926.512662-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmZLzNIUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vwr/Q//STe2XGKI8bAKqP2wbbkzm+ISnK4A
Lqf3FEAIXunxDRspszfXKKV2p4vaIkmOFiwIdtp/kWvd0DQn5+ATXJ/iQtp8aFX/
R+6BQ7EZc2G7fN5fbQuK54+CvmWEpkKEMbXYbd6ivQ14Cijdb3Nbu+w+DYFjS+6C
k2a9lS1bTW7Xcy0fyiO1w6GQiWqtmOH8U3OlQtIrI0EVkDG9OG1LsLuc92/FgkOo
REN+sU+hX1K5fHrvm2CtjYDn/9/B6bJ/It22H1dPgUL9nKvKC67fYzosMtUCOX1M
6XSPjZIuXOmQGeZXHhpSlVwaidxoUjYO98I7nMquxKdCy6yct3geK7ULG/xeQCgD
ML7MGQB4+sTiSWalXUQaziKqF1FIDEvU3HMGXFWnoBL5l56eRp8KS1EI9Eqk9pU3
pk9fJaCkcFnkzPtMFzqPOm5q9zUZ6bGbfYb0hs72TUKplmVDhFo2T1YsW2AOyHZ7
mjuDzUYZX0H7uM1tntA56IgZX+oNOrLvhBt5L5M/BQeCsZFBBUfIcAEaYoL9LwXO
AYgIG3jdqzHHyAUzutJF+XHKinJLMHm0XVYbFmO6saPhFzrUJSNHqT7NzW1DGGTl
OnO8e1WNMX1EcnKvnc6fXyGmM3SgVwy45FsbG/zRnhn4uBKqKtjrh6uX/myA22LK
CSeqSUK9XmXxFNA=
=xjoS
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-25-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig <hch@lst.de> says:
Hi all,
this series converts the SCSI midlayer and LLDDs to use atomic queue
limits API. It is pretty straight forward, except for the mpt3mr
driver which does really weird and probably already broken things by
setting limits from unlocked device iteration callbacks.
I will probably defer the (more complicated) ULD changes to the next
merge window as they would heavily conflict with Damien's zone write
plugging series. With that the series could go in through the SCSI
tree if Jens' ACKs the core block layer bits.
Link: https://lore.kernel.org/r/20240409143748.980206-1-hch@lst.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch to the ->device_configure method instead of ->slave_configure and
update the block limits on the passed in queue_limits instead of using the
per-limit accessors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-12-hch@lst.de
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix indentation of megaraid options help text by adding leading spaces.
Generally help text is indented by couple of spaces more beyond the leading
tab <\t> character.
Signed-off-by: Prasad Pandit <pjp@fedoraproject.org>
Link: https://lore.kernel.org/r/20240311121127.1281159-1-ppandit@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver now includes the print message 'IO is completed, no reset is
required' when a reset is requested but not issued. This message is
displayed only when pending SCSI IO is completed before issuing the reset.
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20231003110021.168862-3-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In BMC environments with concurrent access to multiple registers, certain
registers occasionally yield a value of 0 even after 3 retries due to
hardware errata. As a fix, we have extended the retry count from 3 to 30.
The same errata applies to the mpt3sas driver, and a similar patch has
been accepted. Please find more details in the mpt3sas patch reference
link.
Link: https://lore.kernel.org/r/20230829090020.5417-2-ranjan.kumar@broadcom.com
Fixes: 272652fcbf1a ("scsi: megaraid_sas: add retry logic in megasas_readl")
Cc: stable@vger.kernel.org
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20231003110021.168862-2-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following processes run into a deadlock. CPU 41 was waiting for CPU 29
to handle a CSD request while holding spinlock "crashdump_lock", but CPU 29
was hung by that spinlock with IRQs disabled.
PID: 17360 TASK: ffff95c1090c5c40 CPU: 41 COMMAND: "mrdiagd"
!# 0 [ffffb80edbf37b58] __read_once_size at ffffffff9b871a40 include/linux/compiler.h:185:0
!# 1 [ffffb80edbf37b58] atomic_read at ffffffff9b871a40 arch/x86/include/asm/atomic.h:27:0
!# 2 [ffffb80edbf37b58] dump_stack at ffffffff9b871a40 lib/dump_stack.c:54:0
# 3 [ffffb80edbf37b78] csd_lock_wait_toolong at ffffffff9b131ad5 kernel/smp.c:364:0
# 4 [ffffb80edbf37b78] __csd_lock_wait at ffffffff9b131ad5 kernel/smp.c:384:0
# 5 [ffffb80edbf37bf8] csd_lock_wait at ffffffff9b13267a kernel/smp.c:394:0
# 6 [ffffb80edbf37bf8] smp_call_function_many at ffffffff9b13267a kernel/smp.c:843:0
# 7 [ffffb80edbf37c50] smp_call_function at ffffffff9b13279d kernel/smp.c:867:0
# 8 [ffffb80edbf37c50] on_each_cpu at ffffffff9b13279d kernel/smp.c:976:0
# 9 [ffffb80edbf37c78] flush_tlb_kernel_range at ffffffff9b085c4b arch/x86/mm/tlb.c:742:0
#10 [ffffb80edbf37cb8] __purge_vmap_area_lazy at ffffffff9b23a1e0 mm/vmalloc.c:701:0
#11 [ffffb80edbf37ce0] try_purge_vmap_area_lazy at ffffffff9b23a2cc mm/vmalloc.c:722:0
#12 [ffffb80edbf37ce0] free_vmap_area_noflush at ffffffff9b23a2cc mm/vmalloc.c:754:0
#13 [ffffb80edbf37cf8] free_unmap_vmap_area at ffffffff9b23bb3b mm/vmalloc.c:764:0
#14 [ffffb80edbf37cf8] remove_vm_area at ffffffff9b23bb3b mm/vmalloc.c:1509:0
#15 [ffffb80edbf37d18] __vunmap at ffffffff9b23bb8a mm/vmalloc.c:1537:0
#16 [ffffb80edbf37d40] vfree at ffffffff9b23bc85 mm/vmalloc.c:1612:0
#17 [ffffb80edbf37d58] megasas_free_host_crash_buffer [megaraid_sas] at ffffffffc020b7f2 drivers/scsi/megaraid/megaraid_sas_fusion.c:3932:0
#18 [ffffb80edbf37d80] fw_crash_state_store [megaraid_sas] at ffffffffc01f804d drivers/scsi/megaraid/megaraid_sas_base.c:3291:0
#19 [ffffb80edbf37dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0
#20 [ffffb80edbf37dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0
#21 [ffffb80edbf37de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0
#22 [ffffb80edbf37e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0
#23 [ffffb80edbf37ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0
#24 [ffffb80edbf37ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0
#25 [ffffb80edbf37ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0
#26 [ffffb80edbf37f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0
#27 [ffffb80edbf37f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0
PID: 17355 TASK: ffff95c1090c3d80 CPU: 29 COMMAND: "mrdiagd"
!# 0 [ffffb80f2d3c7d30] __read_once_size at ffffffff9b0f2ab0 include/linux/compiler.h:185:0
!# 1 [ffffb80f2d3c7d30] native_queued_spin_lock_slowpath at ffffffff9b0f2ab0 kernel/locking/qspinlock.c:368:0
# 2 [ffffb80f2d3c7d58] pv_queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/paravirt.h:674:0
# 3 [ffffb80f2d3c7d58] queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/qspinlock.h:53:0
# 4 [ffffb80f2d3c7d68] queued_spin_lock at ffffffff9b8961a6 include/asm-generic/qspinlock.h:90:0
# 5 [ffffb80f2d3c7d68] do_raw_spin_lock_flags at ffffffff9b8961a6 include/linux/spinlock.h:173:0
# 6 [ffffb80f2d3c7d68] __raw_spin_lock_irqsave at ffffffff9b8961a6 include/linux/spinlock_api_smp.h:122:0
# 7 [ffffb80f2d3c7d68] _raw_spin_lock_irqsave at ffffffff9b8961a6 kernel/locking/spinlock.c:160:0
# 8 [ffffb80f2d3c7d88] fw_crash_buffer_store [megaraid_sas] at ffffffffc01f8129 drivers/scsi/megaraid/megaraid_sas_base.c:3205:0
# 9 [ffffb80f2d3c7dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0
#10 [ffffb80f2d3c7dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0
#11 [ffffb80f2d3c7de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0
#12 [ffffb80f2d3c7e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0
#13 [ffffb80f2d3c7ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0
#14 [ffffb80f2d3c7ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0
#15 [ffffb80f2d3c7ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0
#16 [ffffb80f2d3c7f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0
#17 [ffffb80f2d3c7f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0
The lock is used to synchronize different sysfs operations, it doesn't
protect any resource that will be touched by an interrupt. Consequently
it's not required to disable IRQs. Replace the spinlock with a mutex to fix
the deadlock.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Link: https://lore.kernel.org/r/20230828221018.19471-1-junxiao.bi@oracle.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PCI core API pci_dev_id() can be used to get the BDF number for a PCI
device. We don't need to compose it manually. Use pci_dev_id() to simplify
the code a little bit.
Signed-off-by: Jialin Zhang <zhangjialin11@huawei.com>
Link: https://lore.kernel.org/r/20230815025419.3523236-4-zhangjialin11@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PCI core API pci_dev_id() can be used to get the BDF number for a PCI
device. We don't need to compose it manually. Use pci_dev_id() to simplify
the code a little bit.
Signed-off-by: Jialin Zhang <zhangjialin11@huawei.com>
Link: https://lore.kernel.org/r/20230815025419.3523236-3-zhangjialin11@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (ufs, pm80xx, libata-scsi, smartpqi,
lpfc, qla2xxx). We have a couple of major core changes impacting
other systems: Command Duration Limits, which spills into block and
ATA and block level Persistent Reservation Operations, which touches
block, nvme, target and dm (both of which are added with merge commits
containing a cover letter explaining what's going on).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZJ19cSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfZpAQCQBuWR
ELcOhsaG5KzO6xLWcH8mjsOoxffKvazZjTKXlAD5ATEv7++E250oKS3t+yfjae5I
Lc195MlDju85ItUQgfk=
=U9ik
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, pm80xx, libata-scsi, smartpqi,
lpfc, qla2xxx).
We have a couple of major core changes impacting other systems:
- Command Duration Limits, which spills into block and ATA
- block level Persistent Reservation Operations, which touches block,
nvme, target and dm
Both of these are added with merge commits containing a cover letter
explaining what's going on"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (187 commits)
scsi: core: Improve warning message in scsi_device_block()
scsi: core: Replace scsi_target_block() with scsi_block_targets()
scsi: core: Don't wait for quiesce in scsi_device_block()
scsi: core: Don't wait for quiesce in scsi_stop_queue()
scsi: core: Merge scsi_internal_device_block() and device_block()
scsi: sg: Increase number of devices
scsi: bsg: Increase number of devices
scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue
scsi: ufs: ufs-pci: Add support for Intel Arrow Lake
scsi: sd: sd_zbc: Use PAGE_SECTORS_SHIFT
scsi: ufs: wb: Add explicit flush_threshold sysfs attribute
scsi: ufs: ufs-qcom: Switch to the new ICE API
scsi: ufs: dt-bindings: qcom: Add ICE phandle
scsi: ufs: ufs-mediatek: Set UFSHCD_QUIRK_MCQ_BROKEN_RTC quirk
scsi: ufs: ufs-mediatek: Set UFSHCD_QUIRK_MCQ_BROKEN_INTR quirk
scsi: ufs: core: Add host quirk UFSHCD_QUIRK_MCQ_BROKEN_RTC
scsi: ufs: core: Add host quirk UFSHCD_QUIRK_MCQ_BROKEN_INTR
scsi: ufs: core: Remove dedicated hwq for dev command
scsi: ufs: core: mcq: Fix the incorrect OCS value for the device command
scsi: ufs: dt-bindings: samsung,exynos: Drop unneeded quotes
...
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends not
being declared. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-32-schnelle@linux.ibm.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While struct_size() is normally used in situations where the structure
type already has a pointer instance, there are places where no variable
is available. In the past, this has been worked around by using a typed
NULL first argument, but this is a bit ugly. Add a helper to do this,
and replace the handful of instances of the code pattern with it.
Instances were found with this Coccinelle script:
@struct_size_t@
identifier STRUCT, MEMBER;
expression COUNT;
@@
- struct_size((struct STRUCT *)\(0\|NULL\),
+ struct_size_t(struct STRUCT,
MEMBER, COUNT)
Suggested-by: Christoph Hellwig <hch@infradead.org>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: HighPoint Linux Team <linux@highpoint-tech.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: Don Brace <don.brace@microchip.com>
Cc: "Darrick J. Wong" <djwong@kernel.org>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Guo Xuenan <guoxuenan@huawei.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Daniel Latypov <dlatypov@google.com>
Cc: kernel test robot <lkp@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: linux-scsi@vger.kernel.org
Cc: megaraidlinux.pdl@broadcom.com
Cc: storagedev@microchip.com
Cc: linux-xfs@vger.kernel.org
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20230522211810.never.421-kees@kernel.org
In the ongoing effort to replace all fake flexible arrays with true
flexible arrays, replace the sge32, sge64, and sge_skinny members of union
megasas_sgl with true flexible arrays. No binary differences are seen after
this change; sizes were already being manually calculated using the member
struct sizes directly.
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: megaraidlinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230511220957.never.919-kees@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a physical disk is attached directly "without JBOD MAP support" (see
megasas_get_tm_devhandle()) then there is no real error handling in the
driver. Return FAILED instead of SUCCESS.
Fixes: 18365b138508 ("megaraid_sas: Task management support")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230324150134.14696-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If crash_dump_buf is not allocated then crash dump can't be available.
Replace logical 'and' with 'or'.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230324135249.9733-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In kdump kernel mode, the driver works in reduced functionality mode with
some features disabled such as reduced MSI-X count and RDPQ disabled, etc.
However, the firmware is not aware of this mode in some cases, which
results in undefined behavior.
To address this, the driver informs the firmware about the kdump mode
through MPI capabilities bit during driver initialization. This allows
firmware to adjust its behavior accordingly.
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20230302105342.34933-3-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The firmware only supports Logical Disk IDs up to 240 and LD ID 255 (0xFF)
is reserved for deleted LDs. However, in some cases, firmware was assigning
LD ID 254 (0xFE) to deleted LDs and this was causing the driver to mark the
wrong disk as deleted. This in turn caused the wrong disk device to be
taken offline by the SCSI midlayer.
To address this issue, limit the LD ID range from 255 to 240. This ensures
the deleted LD ID is properly identified and removed by the driver without
accidently deleting any valid LDs.
Fixes: ae6874ba4b43 ("scsi: megaraid_sas: Early detection of VD deletion through RaidMap update")
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20230302105342.34933-2-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct MPI2_RAID_SCSI_IO_REQUEST ends with a single SGL, but expects to
copy multiple. Add a flexible array member so the compiler can reason about
the size of the memcpy(). This will avoid the run-time false positive
warning:
memcpy: detected field-spanning write (size 128) of single field "&r1_cmd->io_request->SGL" at drivers/scsi/megaraid/megaraid_sas_fusion.c:3326 (size 16)
This change results in no binary output differences.
Reported-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Link: https://lore.kernel.org/all/88de8faa-56c4-693d-2d3-67152ee72057@diagnostix.dwd.de/
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: megaraidlinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Link: https://lore.kernel.org/r/20230106053153.never.999-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (target, ufs, smartpqi, lpfc). There are
some core changes, mostly around reworking some of our user context
assumptions in device put and moving some code around. The remaining
updates are bug fixes and minor changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY5jjrSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishR9iAPwN++uF
BNlCD36duS8LslKQMPAmFxWt3d/4RWAHsXj2WQEAtu9q8K9PSe1ueb4y+rAEG4oj
2AUQhR3v9ciWBBKlDog=
=JYJC
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (target, ufs, smartpqi, lpfc).
There are some core changes, mostly around reworking some of our user
context assumptions in device put and moving some code around.
The remaining updates are bug fixes and minor changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
scsi: sg: Fix get_user() in call sg_scsi_ioctl()
scsi: megaraid_sas: Fix some spelling mistakes in comment
scsi: core: Use SCSI_SCAN_INITIAL in do_scsi_scan_host()
scsi: core: Use SCSI_SCAN_RESCAN in __scsi_add_device()
scsi: ufs: ufs-mediatek: Remove unnecessary return code
scsi: ufs: core: Fix the polling implementation
scsi: libsas: Do not export sas_ata_wait_after_reset()
scsi: hisi_sas: Fix SATA devices missing issue during I_T nexus reset
scsi: libsas: Add smp_ata_check_ready_type()
scsi: Revert "scsi: hisi_sas: Don't send bcast events from HW during nexus HA reset"
scsi: Revert "scsi: hisi_sas: Drain bcast events in hisi_sas_rescan_topology()"
scsi: ufs: ufs-mediatek: Modify the return value
scsi: ufs: ufs-mediatek: Remove unneeded code
scsi: device_handler: alua: Call scsi_device_put() from non-atomic context
scsi: device_handler: alua: Revert "Move a scsi_device_put() call out of alua_check_vpd()"
scsi: snic: Fix possible UAF in snic_tgt_create()
scsi: qla2xxx: Initialize vha->unknown_atio_[list, work] for NPIV hosts
scsi: qla2xxx: Remove duplicate of vha->iocb_work initialization
scsi: fcoe: Fix transport not deattached when fcoe_if_init() fails
scsi: sd: Use 16-byte SYNCHRONIZE CACHE on ZBC devices
...
Commit 6600593cbd93 ("block: rename BLK_EH_NOT_HANDLED to BLK_EH_DONE")
made it impossible for .eh_timed_out() implementations to call
scsi_done() without causing a crash.
Restore support for SCSI timeout handlers to call scsi_done() as follows:
* Change all .eh_timed_out() handlers as follows:
- Change the return type into enum scsi_timeout_action.
- Change BLK_EH_RESET_TIMER into SCSI_EH_RESET_TIMER.
- Change BLK_EH_DONE into SCSI_EH_NOT_HANDLED.
* In scsi_timeout(), convert the SCSI_EH_* values into BLK_EH_* values.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20221018202958.1902564-3-bvanassche@acm.org
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target); the biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so. Beyond the usual bug fixing and
security class reworks, there aren't a huge number of core changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY0B74yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishW2NAP9CPp2R
7NRmSyxcyVYvtCNUW3WxXh65Gn+KgArmg8XucgEAhUBX1fSjOzpERWEU+UaXitbE
Rb+FbjxSc5YxR+nJ/Qc=
=0Wlp
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target). The biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so.
Beyond the usual bug fixing and security class reworks, there aren't a
huge number of core changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
scsi: mpi3mr: Remove unnecessary cast
scsi: stex: Properly zero out the passthrough command structure
scsi: mpi3mr: Update driver version to 8.2.0.3.0
scsi: mpi3mr: Fix scheduling while atomic type bug
scsi: mpi3mr: Scan the devices during resume time
scsi: mpi3mr: Free enclosure objects during driver unload
scsi: mpi3mr: Handle 0xF003 Fault Code
scsi: mpi3mr: Graceful handling of surprise removal of PCIe HBA
scsi: mpi3mr: Schedule IRQ kthreads only on non-RT kernels
scsi: mpi3mr: Support new power management framework
scsi: mpi3mr: Update mpi3 header files
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix ioc->base_readl() use"
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix writel() use"
scsi: wd33c93: Remove dead code related to the long-gone config WD33C93_PIO
scsi: core: Add I/O timeout count for SCSI device
scsi: qedf: Populate sysfs attributes for vport
scsi: pm8001: Replace one-element array with flexible-array member
scsi: 3w-xxxx: Replace one-element array with flexible-array member
scsi: hptiop: Replace one-element array with flexible-array member in struct hpt_iop_request_ioctl_command()
...
-----BEGIN PGP SIGNATURE-----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=R05e
-----END PGP SIGNATURE-----
Merge tag 'for-6.1/block-2022-10-03' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Christoph:
- handle number of queue changes in the TCP and RDMA drivers
(Daniel Wagner)
- allow changing the number of queues in nvmet (Daniel Wagner)
- also consider host_iface when checking ip options (Daniel
Wagner)
- don't map pages which can't come from HIGHMEM (Fabio M. De
Francesco)
- avoid unnecessary flush bios in nvmet (Guixin Liu)
- shrink and better pack the nvme_iod structure (Keith Busch)
- add comment for unaligned "fake" nqn (Linjun Bao)
- print actual source IP address through sysfs "address" attr
(Martin Belanger)
- various cleanups (Jackie Liu, Wolfram Sang, Genjian Zhang)
- handle effects after freeing the request (Keith Busch)
- copy firmware_rev on each init (Keith Busch)
- restrict management ioctls to admin (Keith Busch)
- ensure subsystem reset is single threaded (Keith Busch)
- report the actual number of tagset maps in nvme-pci (Keith
Busch)
- small fabrics authentication fixups (Christoph Hellwig)
- add common code for tagset allocation and freeing (Christoph
Hellwig)
- stop using the request_queue in nvmet (Christoph Hellwig)
- set min_align_mask before calculating max_hw_sectors (Rishabh
Bhatnagar)
- send a rediscover uevent when a persistent discovery controller
reconnects (Sagi Grimberg)
- misc nvmet-tcp fixes (Varun Prakash, zhenwei pi)
- MD pull request via Song:
- Various raid5 fix and clean up, by Logan Gunthorpe and David
Sloan.
- Raid10 performance optimization, by Yu Kuai.
- sbitmap wakeup hang fixes (Hugh, Keith, Jan, Yu)
- IO scheduler switching quisce fix (Keith)
- s390/dasd block driver updates (Stefan)
- support for recovery for the ublk driver (ZiyangZhang)
- rnbd drivers fixes and updates (Guoqing, Santosh, ye, Christoph)
- blk-mq and null_blk map fixes (Bart)
- various bcache fixes (Coly, Jilin, Jules)
- nbd signal hang fix (Shigeru)
- block writeback throttling fix (Yu)
- optimize the passthrough mapping handling (me)
- prepare block cgroups to being gendisk based (Christoph)
- get rid of an old PSI hack in the block layer, moving it to the
callers instead where it belongs (Christoph)
- blk-throttle fixes and cleanups (Yu)
- misc fixes and cleanups (Liu Shixin, Liu Song, Miaohe, Pankaj,
Ping-Xiang, Wolfram, Saurabh, Li Jinlin, Li Lei, Lin, Li zeming,
Miaohe, Bart, Coly, Gaosheng
* tag 'for-6.1/block-2022-10-03' of git://git.kernel.dk/linux: (162 commits)
sbitmap: fix lockup while swapping
block: add rationale for not using blk_mq_plug() when applicable
block: adapt blk_mq_plug() to not plug for writes that require a zone lock
s390/dasd: use blk_mq_alloc_disk
blk-cgroup: don't update the blkg lookup hint in blkg_conf_prep
nvmet: don't look at the request_queue in nvmet_bdev_set_limits
nvmet: don't look at the request_queue in nvmet_bdev_zone_mgmt_emulate_all
blk-mq: use quiesced elevator switch when reinitializing queues
block: replace blk_queue_nowait with bdev_nowait
nvme: remove nvme_ctrl_init_connect_q
nvme-loop: use the tagset alloc/free helpers
nvme-loop: store the generic nvme_ctrl in set->driver_data
nvme-loop: initialize sqsize later
nvme-fc: use the tagset alloc/free helpers
nvme-fc: store the generic nvme_ctrl in set->driver_data
nvme-fc: keep ctrl->sqsize in sync with opts->queue_size
nvme-rdma: use the tagset alloc/free helpers
nvme-rdma: store the generic nvme_ctrl in set->driver_data
nvme-tcp: use the tagset alloc/free helpers
nvme-tcp: store the generic nvme_ctrl in set->driver_data
...
The megasas_dbg_lvl is a driver level parameter. Do not initialize it in
the probe path. Otherwise we will miss the debug print when binding a
new device to the megaraid driver.
Link: https://lore.kernel.org/r/1663145283-4872-6-git-send-email-kanie@linux.alibaba.com
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove memset() of pd_list and ld_ids in megasas_get_device_list().
These lists will be cleared by megasas_host_device_list_query(),
megasas_get_pd_list(), and megasas_ld_list_query().
Link: https://lore.kernel.org/r/1663145283-4872-5-git-send-email-kanie@linux.alibaba.com
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct the error message logged when allocation of ioc_init_request fails.
Link: https://lore.kernel.org/r/1663145283-4872-3-git-send-email-kanie@linux.alibaba.com
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "id" parameter currently passed to scsi_device_lookup() when removing a
device is incorrect. It should be "ld_target_id %
MEGASAS_MAX_DEV_PER_CHANNEL".
Link: https://lore.kernel.org/r/1663145283-4872-2-git-send-email-kanie@linux.alibaba.com
Fixes: ae6874ba4b43 ("scsi: megaraid_sas: Early detection of VD deletion through RaidMap update")
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix up sysfs show entries to use sysfs_emit()
Link: https://lore.kernel.org/r/20220831140325.396295-1-zhangxuezhi3@gmail.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Xuezhi Zhang <zhangxuezhi1@coolpad.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
One-element arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace one-element array with flexible-array
member in struct MR_DRV_RAID_MAP and refactor the code accordingly.
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Link: https://lore.kernel.org/r/1448f387821833726b99f0ce13069ada89164eb5.1660592640.git.gustavoars@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhanced-by: Kees Cook <keescook@chromium.org> # Change in struct MR_DRV_RAID_MAP_ALL
One-element arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace one-element array with flexible-array
member in struct MR_DRV_RAID_MAP and refactor the the rest of the code
accordingly.
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Link: https://lore.kernel.org/r/4495ce170c8ef088a10f1abe0e7c227368f43242.1660592640.git.gustavoars@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhanced-by: Kees Cook <keescook@chromium.org> # Change in struct MR_FW_RAID_MAP_ALL
The variable mfiStatus is assigned a value but it is never read. The
assignment is redundant and can be removed. Also remove { } as the return
statement does not need to be in its own code block.
Cleans up clang scan build warning:
drivers/scsi/megaraid/megaraid_sas_base.c:4026:7: warning: Although the
value stored to 'mfiStatus' is used in the enclosing expression, the
value is never actually read from 'mfiStatus' [deadcode.DeadStores]
Link: https://lore.kernel.org/r/20220805115042.2340400-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since blk_mq_map_queues() and the .map_queues() callbacks always return 0,
change their return type into void. Most callers ignore the returned value
anyway.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Acked-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20220815170043.19489-3-bvanassche@acm.org
[axboe: fold in fix from Bart]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mostly small bug fixes and trivial updates. The major new core update
is a change to the way device, target and host reference counting is
done to try to make it more robust (this change has soaked for a while
to try to winkle out any bugs).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYveemSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisheaiAP9DPQ70
7hEdak6evXUwlWwlVBvEFAfZlzpHN+uNzUCvpgD+N61RSPhHV1hXu12sVMmjMNEb
pow+ee47Mc0t/OO68jA=
=1yQh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes and trivial updates.
The major new core update is a change to the way device, target and
host reference counting is done to try to make it more robust (this
change has soaked for a while to try to winkle out any bugs)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pm8001: Fix typo 'the the' in comment
scsi: megaraid_sas: Remove redundant variable cmd_type
scsi: FlashPoint: Remove redundant variable bm_int_st
scsi: zfcp: Fix missing auto port scan and thus missing target ports
scsi: core: Call blk_mq_free_tag_set() earlier
scsi: core: Simplify LLD module reference counting
scsi: core: Make sure that hosts outlive targets
scsi: core: Make sure that targets outlive devices
scsi: ufs: ufs-pci: Correct check for RESET DSM
scsi: target: core: De-RCU of se_lun and se_lun acl
scsi: target: core: Fix race during ACL removal
scsi: ufs: core: Correct ufshcd_shutdown() flow
scsi: ufs: core: Increase the maximum data buffer size
scsi: lpfc: Check the return value of alloc_workqueue()
When alloc ctrl mem fails, the reply_map will subsequently be freed in
megasas_free_ctrl_mem(). No need to free it in megasas_alloc_ctrl_mem().
Link: https://lore.kernel.org/r/1659424740-46918-1-git-send-email-kanie@linux.alibaba.com
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When allocating log_to_span fails, kfree(instance->ctrl_context) is called
twice. Remove redundant call.
Link: https://lore.kernel.org/r/1659424729-46502-1-git-send-email-kanie@linux.alibaba.com
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr). The main driver change that might cause issues on down the
road is the conversion of some of our oldest surviving drivers to the
DMA API (should only affect m68k). The only major core change is the
rework of async resume; the rest are either completely trivial or for
updating deprecated APIs.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYuvakyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfvOAP4m0N6b
e3JwoBtB1c0JMKv6G4gka8suEG8p5f4khDu8wwD+LfGUCzG49Y5Ts7rByXfEiGgO
krSdwsAZiV6yKg/HuPw=
=Ak9L
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr).
The main driver change that might cause issues on down the road is the
conversion of some of our oldest surviving drivers to the DMA API
(should only affect m68k).
The only major core change is the rework of async resume; the rest are
either completely trivial or for updating deprecated APIs"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (195 commits)
scsi: target: Remove XDWRITEREAD emulated support
scsi: megaraid: Remove the static variable initialisation
scsi: ch: Do not initialise statics to 0
scsi: ufs: core: Fix spelling mistake "Cannnot" -> "Cannot"
scsi: target: iscsi: Do not require target authentication
scsi: target: iscsi: Allow AuthMethod=None
scsi: target: iscsi: Support base64 in CHAP
scsi: target: iscsi: Add support for extended CDB AHS
scsi: ufs: dt-bindings: Add SC8280XP binding
scsi: target: iscsi: Fix clang -Wformat warnings
scsi: ufs: core: Read device property for ref clock
scsi: libsas: Resume SAS host for phy reset or enable via sysfs
scsi: hisi_sas: Modify v3 HW SATA completion error processing
scsi: hisi_sas: Relocate DMA unmap of SMP task
scsi: hisi_sas: Remove unnecessary variable to hold DMA map elements
scsi: hisi_sas: Call hisi_sas_slave_configure() from slave_configure_v3_hw()
scsi: mpi3mr: Delete a stray tab
scsi: mpi3mr: Unlock on error path
scsi: mpi3mr: Reduce VD queue depth on detecting throttling
scsi: mpi3mr: Resource Based Metering
...
