Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to avoid potential overflows in print_constraints we
better replace sprintf() with scnprintf().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
We weren't taking into account the already used buffer when telling
sprintf() where to print to.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't consider a failure to add the sysfs node as a problem,
so use sysfs_create_link_nowarn() so that we don't print a
backtrace when duplicated files exist. Also, downgrade the printk
message to a debug statement so that we're quiet here. This
allows multiple drivers to request a CPU's regulator so that
CPUfreq and AVSish drivers can coexist.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code does not set regulators->irq_ldo_lim and regulators->irq_uvov,
so it actually calls free_irq(0, regulators) twice in remove() but does not
free the irq actually used.
Convert to use devm_request_threaded_irq instead and then we don't need to
take care the clean up irq so remove irq_ldo_lim and irq_uvov from
struct da9063_regulators. Note, regulators->irq_uvov is not used at all in
current code.
There is a slightly change in this patch, it will return error in probe()
if devm_request_threaded_irq fails. If the irq is optional, it should be
fine to allow platform_get_irq_byname fails. But current code does not
allow platform_get_irq_byname fails. So I think the reason to allow
request irq failure is just because the irq leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the unused variable build warning for reg_matches that appears
during the compilation of the DA9062 regulator driver.
da9062-regulator.c: In function da9062_regulator_probe:
da9062-regulator.c:727:29: warning: unused variable reg_matches
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix broken probe of da9052 regulators, which since commit b3f6c73db732
("mfd: da9052-core: Fix platform-device id collision") use a
non-deterministic platform-device id to retrieve static regulator
information. Fortunately, adequate error handling was in place so probe
would simply fail with an error message.
Update the mfd-cell ids to be zero-based and use those to identify the
cells when probing the regulator devices.
Fixes: b3f6c73db732 ("mfd: da9052-core: Fix platform-device id collision")
Cc: stable <stable@vger.kernel.org> # v3.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Setting the set_voltage_time_sel callback to the standard function
regulator_set_voltage_time_sel enables the regulator to actually honor
ramp-delays when during regulator_set_voltage calls.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extra space between platform prefix and driver name in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add BUCK and LDO regulator driver support for DA9062
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code should handle more than 32 bits here because "id"
can be a value up to MAX77686_REGULATORS (currently 34).
Convert the gpio_enabled type to DECLARE_BITMAP and use
test_bit/set_bit.
Fixes: 3307e9025d29 ("regulator: max77686: Add GPIO control")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch adds support for the 1.175V mode on the LDO1 regulator on the
wm5110. This is need as part of the low power sleep mode operation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded semicolons after the switch statement to satisfy
coccicheck.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function name in kernel-doc for regulator_map_voltage_linear_range()
was wrong.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not necessary to have regulator init data for a regulator. This
patch removes the necessity of this data and handles a NULL pointer
properly.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Voltage regulators can have (unregulated) current limits too, so we should
probably output both voltage and current for all regulators.
Holding the rdev->mutex actually conflicts with _regulator_get_current_limit
but also is not really necessary, as the global regulator_list_mutex already
protects us from the regulator vanishing while we go through the list.
On the rk3288-firefly the summary now looks like:
regulator use open bypass voltage current min max
-------------------------------------------------------------------------------
vcc_sys 0 12 0 5000mV 0mA 5000mV 5000mV
vcc_lan 1 1 0 3300mV 0mA 3300mV 3300mV
ff290000.ethernet 0mV 0mV
vcca_33 0 0 0 3300mV 0mA 3300mV 3300mV
vcca_18 0 0 0 1800mV 0mA 1800mV 1800mV
vdd10_lcd 0 0 0 1000mV 0mA 1000mV 1000mV
[...]
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On modern systems the regulator hierarchy can get quite long and nested
with regulators supplying other regulators. In some cases when debugging
it might be nice to get a tree of these regulators, their consumers
and the regulation constraints in one go.
To achieve this add a regulator_summary sysfs node, similar to
clk_summary in the common clock framework, that walks the regulator
list and creates a tree out of the regulators, their consumers and
core per-regulator settings.
On a rk3288-firefly the regulator_summary would for example look
something like:
regulator use open bypass value min max
-----------------------------------------------------------------------
vcc_sys 0 12 0 5000mV 5000mV 5000mV
vcc_lan 1 1 0 3300mV 3300mV 3300mV
ff290000.ethernet 0mV 0mV
vcca_33 0 0 0 3300mV 3300mV 3300mV
vcca_18 0 0 0 1800mV 1800mV 1800mV
vdd10_lcd 0 0 0 1000mV 1000mV 1000mV
vccio_sd 0 0 0 3300mV 3300mV 3300mV
vcc_20 0 3 0 2000mV 2000mV 2000mV
vcc18_lcd 0 0 0 1800mV 1800mV 1800mV
vcc_18 0 2 0 1800mV 1800mV 1800mV
ff100000.saradc 0mV 0mV
ff0d0000.dwmmc 1650mV 1950mV
vdd_10 0 0 0 1000mV 1000mV 1000mV
vdd_log 0 0 0 1100mV 1100mV 1100mV
vcc_io 0 3 0 3300mV 3300mV 3300mV
ff0f0000.dwmmc 3300mV 3400mV
vcc_flash 1 1 0 1800mV 1800mV 1800mV
ff0f0000.dwmmc 1700mV 1950mV
vcc_sd 1 1 0 3300mV 3300mV 3300mV
ff0c0000.dwmmc 3300mV 3400mV
vcc_ddr 0 0 0 1200mV 1200mV 1200mV
vdd_gpu 0 0 0 1000mV 850mV 1350mV
vdd_cpu 0 1 0 900mV 850mV 1350mV
cpu0 900mV 900mV
vcc_5v 0 2 0 5000mV 5000mV 5000mV
vcc_otg_5v 0 0 0 5000mV 5000mV 5000mV
vcc_host_5v 0 0 0 5000mV 5000mV 5000mV
regulator-dummy 0 0 0 0mV 0mV 0mV
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidy up error reporting and move rpm reference retrieval out of the for
loop for improved readability.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modeling the individual RPM resources as platform devices consumes at
least 12-15kb of RAM, just to hold the platform_device structs. Rework
this to instead have one device per pmic exposed by the RPM.
With this representation we can more accurately define the input pins on
the pmic and have the supply description match the data sheet.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor out all custom property parsing code from the probe function
into a function suitable for regulator_desc->of_parse_cb usage.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver itself should not flag regulators as being DRMS compatible,
this should come from board or dt files.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pdata is assigned to &pdata_of, however, pdata_of becomes dead (when it
goes out of scope) so pdata effectively becomes a dead pointer to the
out of scope object. This is detected by static analysis:
[drivers/regulator/max8660.c:411]: (error) Dead pointer usage.
Pointer 'pdata' is dead if it has been assigned '&pdata_of' at line 404.
Move declaration of pdata_of so it is always in scope.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of resolving regulator supplies during registration move this to
the time of a consumer retrieving a handle. The benefit is that it's
possible for one driver to register regulators with internal
dependencies out of order.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the driver by removing board file support and letting
regulator core to parse DT.
The max77693 regulator driver is used only on Exynos based boards which
are DT-only. Board files for Exynos are not supported.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If multiple regulator devices of the same type exist in a system,
the regulator driver assigns generic names for the regulators it
provides, and debugfs is enabled, the regulator subsystem attempts
to create multiple entries with the same name in the regulator debugfs
directory. This fails for all but the first regulator, resulting in
multiple "Failed to create debugfs directory" log entries.
To avoid the problem, prepend the debugfs directory name for a regulator
with its parent device name if available, but only if no explicit
regulator name was provided.
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex lock is not used at all, remove it.
The *vmmc_regulator is not necessary, use a local variable in
stw481x_vmmc_regulator_probe() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Palmas driver is used to cater to even TPS659038 but TPS659038 does not have
REGEN3 resource. Adding another field in the driver data to check on that.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
