Improve mdio master read/write by using singe mii read/write lo/hi.
In a read and write we need to poll the mdio master regs in a busy loop
to check for a specific bit present in the upper half of the reg. We can
ignore the other half since it won't contain useful data. This will save
an additional useless read for each read and write operation.
In a read operation the returned data is present in the mdio master reg
lower half. We can ignore the other half since it won't contain useful
data. This will save an additional useless read for each read operation.
In a read operation it's needed to just set the hi half of the mdio
master reg as the lo half will be replaced by the result. This will save
an additional useless write for each read operation.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be useful to read/write just the lo or hi half of a reg.
This is especially useful for phy poll with the use of mdio master.
The mdio master reg is composed by the first 16 bit related to setup and
the other half with the returned data or data to write.
Refactor the mii function to permit single mii read/write of lo or hi
half of the reg.
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2481d206fae7884cd07014fd1318e63af35e99eb.
The Documentation is very confusing about the topic.
The cache logic for hi and lo is wrong and actually miss some regs to be
actually written.
What the Documentation actually intended was that it's possible to skip
writing hi OR lo if half of the reg is not needed to be written or read.
Revert the change in favor of a better and correct implementation.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumption that Documentation was right about how this value work was
wrong. It was discovered that the length value of the mgmt header is in
step of word size.
As an example to process 4 byte of data the correct length to set is 2.
To process 8 byte 4, 12 byte 6, 16 byte 8...
Odd values will always return the next size on the ack packet.
(length of 3 (6 byte) will always return 8 bytes of data)
This means that a value of 15 (0xf) actually means reading/writing 32 bytes
of data instead of 16 bytes. This behaviour is totally absent and not
documented in the switch Documentation.
In fact from Documentation the max value that mgmt eth can process is
16 byte of data while in reality it can process 32 bytes at once.
To handle this we always round up the length after deviding it for word
size. We check if the result is odd and we round another time to align
to what the switch will provide in the ack packet.
The workaround for the length limit of 15 is still needed as the length
reg max value is 0xf(15)
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Fixes: 90386223f44e ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch sends autocast mib in little-endian. This is problematic for
big-endian system as the values needs to be converted.
Fix this by converting each mib value to cpu byte order.
Fixes: 5c957c7ca78c ("net: dsa: qca8k: add support for mib autocast in Ethernet packet")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header and the data of the skb for the inband mgmt requires
to be in little-endian. This is problematic for big-endian system
as the mgmt header is written in the cpu byte order.
Fix this by converting each value for the mgmt header and data to
little-endian, and convert to cpu byte order the mgmt header and
data sent by the switch.
Fixes: 5950c7c0a68c ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drivers could refuse to offload a LAG configuration for a variety of
reasons, mainly having to do with its TX type. Additionally, since DSA
masters may now also be LAG interfaces, and this will translate into a
call to port_lag_join on the CPU ports, there may be extra restrictions
there. Propagate the netlink extack to this DSA method in order for
drivers to give a meaningful error message back to the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
of_device_get_match_data is called on priv->dev before priv->dev is
actually set. Move of_device_get_match_data after priv->dev is correctly
set to fix this kernel panic.
Fixes: 3bb0844e7bcd ("net: dsa: qca8k: cache match data to speed up access")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220904215319.13070-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The same function to read the switch id is used by drivers based on
qca8k family switch. Move them to common code to make them accessible
also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port LAG functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port VLAN functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Also drop exposing busy_wait and make it static.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port mirror functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same port FDB/MDB function are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Also drop bulk read/write functions and make them static
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same set age, MTU and port enable/disable function are used by
driver based on qca8k family switch.
Move them to common code to make them accessible also by other drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same bridge functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same logic to disable/enable port, set eee and get ethtool stats is
used by drivers based on qca8k family switch.
Move it to common code to make it accessible also by other drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same mib function is used by drivers based on qca8k family switch.
Move it to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same ATU function are used by drivers based on qca8k family switch.
Move the bulk read/write helper to common code to declare these shared
ATU functions in common code.
These helper will be dropped when regmap correctly support bulk
read/write.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same reg table and read/write/rmw function are used by drivers
based on qca8k family switch.
Move them to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same MIB struct is used by drivers based on qca8k family switch. Move
it to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some switch may not support mib autocast feature and require the legacy
way of reading the regs directly.
Make the mib autocast feature optional and permit to declare support for
it using match_data struct in a dedicated qca8k_info_ops struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using of_device_get_match_data is expensive. Cache match data to speed
up access and rework user of match data to use the new cached value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move qca8k driver to qca dir in preparation for code split and
introduction of ipq4019 switch based on qca8k.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Populate the supported interfaces and MAC capabilities for the AR9331
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.
What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.
This message can be seen in a loop, and it hangs the reboot process there:
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
So why 3?
A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:
dsa_slave_create
-> netdev_upper_dev_link
-> __netdev_upper_dev_link
-> __netdev_adjacent_dev_insert
-> dev_hold
So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.
Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.
It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.
So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.
However, complications arise really quickly.
The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).
Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.
So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.
So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.
The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.
The answer to that question lies in this comment above device_link_add:
* A side effect of the link creation is re-ordering of dpm_list and the
* devices_kset list by moving the consumer device and all devices depending
* on it to the ends of these lists (that does not happen to devices that have
* not been registered when this function is called).
so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.
Fixes: 2f1e8ea726e9 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that all external port are actually isolated from each other,
so no packets are leaked.
Fixes: ec6698c272de ("net: dsa: add support for Atheros AR9331 built-in switch")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of this switch we work with 32bit registers on top of 16bit
bus. Some registers (for example access to forwarding database) have
trigger bit on the first 16bit half of request and the result +
configuration of request in the second half. Without this patch, we would
trigger database operation and overwrite result in one run.
To make it work properly, we should do the second part of transfer
before the first one is done.
So far, this rule seems to work for all registers on this switch.
Fixes: ec6698c272de ("net: dsa: add support for Atheros AR9331 built-in switch")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210803063746.3600-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 54a0ed0df496 ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.
New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.
Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.
The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.
The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.
Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.
No behavior change except for the added prints is intended at this time.
$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[ 60.315148] br0: port 1(sw0p2) entered blocking state
[ 60.320350] br0: port 1(sw0p2) entered disabled state
[ 60.327839] device sw0p2 entered promiscuous mode
[ 60.334905] br0: port 1(sw0p2) entered blocking state
[ 60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the ar9331 DSA driver to use the finalised link parameters in
mac_link_up() rather than the parameters in mac_config().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set variable 'mbus' static
since new value always be assigned before use it.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide basic support for Atheros AR9331 built-in switch. So far it
works as port multiplexer without any hardware offloading support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
