renesas_usbhs driver can switch DMA/PIO transfer by using handler,
and each handler have push/pop direction.
But unfortunately, current dma push handler didn't a path
which calls usbhs_pipe_enable(). Thus, dma transfer never happened.
this patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If renesas_usbhs or DMAEngine interrupt didn't happen by a certain cause,
urb->ep will be NULL by usb time out.
Then, host mode will access to it and crash kernel.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the missing unlock on the error handle path in function
net2272_irq().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The res_name is used for the name construction of a DT property as
follows:
sprintf(res_name, "port%d-mode", id);
Hence, res_name must be at least 11 characters long in order to store
the name including the terminating '\0'.
While at it, use to snprintf() rather than sprintf() when accessing this
buffer.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, when FIFO_ERR happens, we stop the dma, wait for it to become
idle and then reset the whole MAC_RX logic (and after that we must re-set
multicast addresses and also re-enable MAC_RX when we're finally ready to
accept new packets). This leads to CRC errors on high number of incoming
packets and is not needed according to the datasheet.
This patch fixes it by the following steps:
1) remove this reset in pch_gbe_stop_receive(), which causes some functions
to not be used anywhere
2) remove already unused functions pch_gbe_wait_clr_bit_irq() and
pch_gbe_mac_reset_rx() to correctly build
3) move pch_gbe_enable_mac_rx() out of pch_gbe_start_receive() to
pch_gbe_up() where it's only needed after we've removed the MAC_RX reset
4) rename pch_gbe_start/stop_receive() to pch_gbe_enable/disable_dma_rx()
to more precisely reflect what the functions are now doing.
After these changes we already don't see the CRC errors and gain some
increase in RX processing speed.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we were in RX_FIFO_ERR state and entered pch_gbe_napi_poll(), we'll
anyway clean some rx space and thus can continue to receive more packets.
Currently, we re-set the RX_FIFO_ERR in situations when we've exhausted our
budget for RX cleaning or cleaned some TX packets. Removing it gives us
+20%-40% speed increase and a lot less of RX_FIFO_ERRors reported.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move MAC_RX-related bits into separate functions.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"Fixes for intel and nouveau mainly.
- intel: disable HSW by default, sdvo fixes, link train regression
fix
- nouveau: acpi rom loading regression fix, with a few other fixes
from the rework
-core: just other minor fixes and race fixes for ttm."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm/ttm: Fix a theoretical race in ttm_bo_cleanup_refs()
drm/ttm: Fix a theoretical race
drm: platform: Don't initialize driver-private data
drm/debugfs: remove redundant info from gem_names
drm: fb: cma: Fail gracefully on allocation failure
drm: fb: cma: Fix typo in debug message
drm/nouveau/clock: fix missing pll type/addr when matching default entry
drm/nouveau/fb: fix reporting of memory type on GF8+ IGPs
drm/nv41/vm: don't init hw pciegart on boards with agp bridge
drm/nouveau/bios: fetch full 4KiB block to determine ACPI ROM image size
drm/nouveau: validate vbios size
drm/nouveau: warn when trying to free mm which is still in use
drm/nouveau: fix nouveau_mm/nouveau_mm_node leak
drm/nouveau/bios: improve error handling when reading the vbios from ACPI
drm/nouveau: handle same-fb page flips
drm/i915: Initialize obj->pages before use by i915_gem_object_do_bit17_swizzle()
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
drm/i915: Insert i915_preliminary_hw_support variable.
drm/i915: shut up spurious WARN in the gtt fault handler
Revert "drm/i915: Try harder to complete DP training pattern 1"
...
Trivial dependency issue, not noticed before as the only user of MMIO
also needs I2C.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQfq6dAAoJELSic+t+oim9KJMP/jp9p8GD6VDnZDXJ2BLLk1Kg
RflVff/rwBlM8mTCK8CFbtpvEYHEMWjWP4i3cEAr8lsJmIe+fEl407SV8cW8CRpO
iJ97JU/Vf0Juuh5ga03dRdiaaewr/uFWugU1YBKe/FWFRJD7e9L5s+P1s0axhe3N
n5wDfYuIY6+bqxrkdrzrzSBqRf800jrR9hAsBrnlIi+f5YKvuo3QXi8zkYE/W9et
U2uHI2ft49EIPJPNszfxn6mF193tbNABXJhn9xFluhEPl368PJCx7Q1zznrYK0va
RyotNVIn+SLo/k9OeBVzDIX5sMoQMINCazpb3eDlJH+NMZ905KmxL/5J7ESBFSxa
NKLAlWSNX6c9vfiGXG95P5DxoK1lY1POoDI6PI70Qf1O82e8U5qSZrE2TTcAUjdi
3MyUDh8Mq2MEYRjjHkrtOJewY1Khz1QsA744o3Gvz9fEsSXOx8VkYdgZdUt+PHCj
sn+2DWQA6zSK1gZqVWym6Y8nIN1e+ALYnZSGAmnfJcsHdGf3FrUbgUp1CqPmQ1Xz
t+zscl/lQdypOk3wXkwq/lScRxRRgomeS9lHt3qpGbjuip+QKhJsJTGjcjvmnHFt
qJOiBoPdK2Gp2hbKRRZlHx1fdt931d2ZHD2jzpZGyZz0wJE09vFhzm4V8NUH3EXu
HX7i4ibN4DLCCoZ7Z1Im
=DPiU
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-mmio' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"regmap: Fix for dependencies for MMIO
Trivial dependency issue, not noticed before as the only user of MMIO
also needs I2C."
* tag 'regmap-fix-mmio' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: select REGMAP if REGMAP_MMIO and REGMAP_IRQ enabled
In theory, that function could release the lru lock between
checking for bo on ddestroy list and a successful reserve if the bo
was already reserved, and the function was called with waiting reserves
allowed.
However, all current reservers of a bo on the ddestroy list would
atomically take the bo off the list after a successful reserve so this
race should not have been hit, so no need to backport for stable.
This patch also fixes a case found by Maarten Lankhorst where
ttm_mem_evict_first called with no_wait_gpu would incorrectly
spin waiting for bo idle if trying to evict a busy buffer that
also sits on the ddestroy list.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm_mem_evict_first function could theoretically drop the
lru lock without retrying if a reservation from off the LRU list
ended up waiting.
However, since currently there are no users that could cause a wait
in that situation so this is not suitable for stable
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Platform device drivers usually use the driver-private data for their
own purposes. Having it overwritten by drm_platform_init() is confusing
and error-prone.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's a relic of "drm: Convert proc files to seq_file and introduce debugfs",
which wrongly converted DRM_INFO + sprintf to 2 seq_printfs.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Gamari <bgamari@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm_gem_cma_create() function never returns NULL but rather an error
encoded in the return value using the ERR_PTR() macro. Callers therefore
need to check for errors using the IS_ERR() macro. This change allows
drivers to handle contiguous DMA allocation failures gracefully.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The debug message showing the resolution of a framebuffer to be
allocated is missing a closing parenthesis.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When system enters sleep, non-boot CPUs will be disabled.
Cpufreq stats sysfs is created when the CPU is up, but it is not
freed when the CPU is going down. This will cause memory leak.
Signed-off-by: xiaobing tu <xiaobing.tu@intel.com>
Signed-off-by: guifang tang <guifang.tang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If pm_genpd_attach_cpudidle failed we leak memory stored in 'cpu_data'.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Memory is allocated with kzalloc() and assigned to
'physical_node'. Then 'physical_node->node_id' is initialized with a
call to 'find_first_zero_bit()', if that results in a value greater
than ACPI_MAX_PHYSICAL_NODE we'll end up jumping to the 'err:' label
and there leave the function and let 'physical_node' go out of scope
and leak the memory we allocated.
This patch fixes the leak by simply freeing the unused/unneeded memory
pointed to by 'physical_node' just before we jump to 'err:'.
[rjw: The problem has been introduced by commit 1033f90 (ACPI: Allow
ACPI binding with USB-3.0 hub), which is new in 3.7-rc.]
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ramster uses network interfaces that are only present when
CONFIG_NET is enabled, so it should depend on NET.
Fixes these build errors:
drivers/built-in.o: In function `sc_kref_release':
tcp.c:(.text+0x24b9af): undefined reference to `sock_release'
drivers/built-in.o: In function `r2net_open_listening_sock':
tcp.c:(.text+0x24ca2b): undefined reference to `sock_create'
tcp.c:(.text+0x24cb91): undefined reference to `sock_release'
drivers/built-in.o: In function `r2net_recv_tcp_msg':
tcp.c:(.text+0x24cdbd): undefined reference to `sock_recvmsg'
drivers/built-in.o: In function `r2net_send_tcp_msg':
tcp.c:(.text+0x24d341): undefined reference to `sock_sendmsg'
drivers/built-in.o: In function `r2net_start_connect':
tcp.c:(.text+0x24d8fa): undefined reference to `sock_create'
drivers/built-in.o: In function `r2net_shutdown_sc':
tcp.c:(.text+0x24e30c): undefined reference to `kernel_sock_shutdown'
drivers/built-in.o: In function `r2net_accept_one':
tcp.c:(.text+0x24f392): undefined reference to `sock_create_lite'
tcp.c:(.text+0x24f3c3): undefined reference to `sock_release'
drivers/built-in.o: In function `r2net_stop_listening':
(.text+0x250f63): undefined reference to `sock_release'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: konrad.wilk@oracle.com
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Vincent Penquerc'h <vincent.penquerch@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change 130f315a (staging: zram: remove special handle of uncompressed page)
introduced a bug in the handling of incompressible pages which resulted in
memory allocation failure for such pages.
When a page expands on compression, say from 4K to 4K+30, we were trying to
do zsmalloc(pool, 4K+30). However, the maximum size which zsmalloc can
allocate is PAGE_SIZE (for obvious reasons), so such allocation requests
always return failure (0).
For a page that has compressed size larger than the original size (this may
happen with already compressed or random data), there is no point storing
the compressed version as that would take more space and would also require
time for decompression when needed again. So, the fix is to store any page,
whose compressed size exceeds a threshold (max_zpage_size), as-it-is i.e.
without compression. Memory required for storing this uncompressed page can
then be requested from zsmalloc which supports PAGE_SIZE sized allocations.
Lastly, the fix checks that we do not attempt to "decompress" the page which
we stored in the uncompressed form -- we just memcpy() out such pages.
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Reported-by: viechweg@gmail.com
Reported-by: paerley@gmail.com
Reported-by: wu.tommy@gmail.com
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Struct usb_hub_descriptor.ss.DeviceRemovable has been defined as __le16
and (__force__ __u16) doesn't need.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When setting usb port's acpi power resource, there will be some xhci hub requests.
This will cause dead lock since xhci->lock has been held before setting acpi power
resource in the xhci_hub_control(). The usb_acpi_power_manageable() function might
fall into sleep so release xhci->lock before invoking it.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The default kernel mapping for the pages allocated for the binder
buffers is never used. Set the __GFP_HIGHMEM flag when allocating
these pages so we don't needlessly use low memory pages that may
be required elsewhere.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a thread or process exited while a reply, one-way transaction or
death notification was pending, the struct holding the pending work
was leaked.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before use the request and response queue addr, make sure it has wrote
to the registers.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`labpc_common_detach()` is called by the comedi core to clean up if
either `labpc_attach()` (including the one in the "ni_labpc_cs" module)
or `labpc_attach_pci()` returns an error. It assumes the `thisboard`
macro (expanding to `((struct labpc_board_struct *)dev->board_ptr)`) is
non-null. This is a valid assumption if `labpc_attach()` fails, but not
if `labpc_attach_pci()` fails, leading to a possible NULL pointer
dereference.
Check `thisboard` at the top of `labpc_common_detach()` and return early
if it is `NULL`. This is okay because the only other thing that could
have been allocated is `dev->private` and that is freed by the comedi
core, not by this function.
Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`das08_detach()` is called by the comedi core to clean up if either
`das08_attach()` or `das08_attach_pci()` returns an error. It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null. This is a valid assumption if `das08_attach()` fails, but not
if `das08_attach_pci()` fails, leading to a possible NULL pointer
dereference.
Check `thisboard` at the top of `das08_detach()` and return early if it
is `NULL`. This is okay because the only other thing that could have
been allocated is `dev->private` and that is freed by the comedi core,
not by this function.
Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`pc263_detach()` is called by the comedi core to clean up if either
`pc263_attach()` or `pc263_attach_pci()` returns an error. It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null. This is a valid assumption if `pc263_attach()` fails, but not
if `pc263_attach_pci()` fails, leading to a possible NULL pointer
dereference.
Check `thisboard` at the top of `pc263_detach()` and return early if it
is `NULL`. This is okay because no other resources need cleaning up in
this case.
Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`pc236_detach()` is called by the comedi core to clean up if either
`pc236_attach()` or `pc236_attach_pci()` returns an error. It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null. This is a valid assumption if `pc236_attach()` fails, but not
if `pc236_attach_pci()` fails, leading to a possible NULL pointer
dereference.
Check `thisboard` at the top of `pc236_detach()` and return early if it
is `NULL`. This is okay because the only other thing that could have
been allocated is `dev->private` and that is freed by the comedi core,
not by this function.
Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`pc236_detach()` is called by the comedi core if it attempted to attach
a device and failed. `pc236_detach()` calls `pc236_intr_disable()` if
the comedi device private data pointer (`devpriv`) is non-null. This
test is insufficient as `pc236_intr_disable()` accesses hardware
registers and the attach routine may have failed before it has saved
their I/O base addresses.
Fix it by checking `dev->iobase` is non-zero before calling
`pc236_intr_disable()` as that means the I/O base addresses have been
saved and the hardware registers can be accessed. It also implies the
comedi device private data pointer is valid, so there is no need to
check it.
Cc: <stable@vger.kernel.org> # 3.5.x, 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`dio200_detach()` is called by the comedi core to clean up if either
`dio200_attach()` or `dio200_attach_pci()` return an error. It assigns
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null. In the case of a previous call to `dio200_attach()` it won't
be `NULL` because the comedi core will have pointed it to one of the
elements of `dio200_boards[]`, but in the case of a previous call to
`dio200_attach_pci()` it could be `NULL`, leading to a null pointer
dereference.
Check that `thisboard` is valid at the top of `dio200_detach()` and
return early if it is `NULL`. This is okay because the only other thing
that could have been allocated is `dev->private` and that is freed by
the comedi core, not by this function.
Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`pci_8255_detach()` will be called by the comedi core if
`pci_8255_attach_pci()` returns an error. It currently assumes that
both `board` (assigned from the return value of `comedi_board(dev)`) and
`devpriv` (assigned from `dev->private`) are non-null, but they might
be null, leading to a null pointer dereference.
`pci_8255_detach()` doesn't need to do anything if either `board` or
`devpriv` are null, so just return early in this case.
Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a small patch to fix a problem caused by a previous patch that
removed the callback function. The callback remove patch:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=1de02225358988e8fd48d1dc3fd12336bbae258a
I finally booted my dev machine on the latest kernel (running Debian
here so it's still on 3.2 normally) to test the ni_daq_700 driver with
my test program and noticed this bug.
Shift the DIO_R read result to bits 8..15 Digital direction
configuration: channels 0-7 output, 8-15 input (8225 device emu as port
A output, port B input, port C N/A).
Cc: <stable@vger.kernel.org> # 3.6.x
Signed-off-by: Fred Brooks <nsaspook@nsaspook.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the error path of registering memory when there's a failure to
allocate a chunk from the memory pool, we try to free the same chunk
we just failed to allocate, which will BUG().
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
async.c has provided synchronization mechanism on async_schedule_*,
so use async_synchronize_full_domain to sync caching firmware instead
of reinventing the wheel.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly 'firmware_buf' is introduced to make all loading requests
to share one firmware kernel buffer, so firmware_buf should
be used in direct loading for saving memory and speedup firmware
loading.
Secondly, the commit below
abb139e75c2cdbb955e840d6331cb5863e409d0e(firmware:teach
the kernel to load firmware files directly from the filesystem)
introduces direct loading for fixing udev regression, but it
bypasses the firmware cache meachnism, so this patch enables
caching firmware for direct loading case since it is still needed
to solve drivers' dependency during system resume.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several loading requests may be pending on one same
firmware buf, and this patch moves fw_map_pages_buf()
before complete_all(&fw_buf->completion) and let all
requests see the mapped 'buf->data' once the loading
is completed.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under 'Opportunistic sleep' situation, system sleep might be
triggered very frequently, so the uncahce work may not be completed
before caching firmware during next suspend.
This patch cancels the uncache work before caching firmware to
fix the problem above.
Also this patch optimizes the cacheing firmware mechanism a bit by
only storing one firmware cache entry for one firmware image.
So if the firmware is still cached during suspend, it doesn't need
to be loaded from user space any more.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes from Ben, off note:
ACPI ROM regression fix,
some IGP and AGP regressions fixes from rework fallout.
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/clock: fix missing pll type/addr when matching default entry
drm/nouveau/fb: fix reporting of memory type on GF8+ IGPs
drm/nv41/vm: don't init hw pciegart on boards with agp bridge
drm/nouveau/bios: fetch full 4KiB block to determine ACPI ROM image size
drm/nouveau: validate vbios size
drm/nouveau: warn when trying to free mm which is still in use
drm/nouveau: fix nouveau_mm/nouveau_mm_node leak
drm/nouveau/bios: improve error handling when reading the vbios from ACPI
drm/nouveau: handle same-fb page flips
Commit 7f8d4cad1e4e ("Input: extend the number of event (and other)
devices") made evdev, joydev and mousedev to embed struct cdev into
their respective structures representing input devices.
Unfortunately character device structure may outlive the parent
structure unless we do not set it up as parent of character device so
that it will stay pinned until character device is freed.
Also, now that parent structure is pinned while character device exists
we do not need to pin and unpin it every time user opens or closes it.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This issue is a regression from 70790f4f819875e8f390871fd15bbbf823f28e1b,
and causes us to miss a special-case for C51 (NV4E) chipsets and return
the wrong reference frequency for the VPLLs.
Should fix fdo#56202
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Rather than re-inventing the wheel we can use the hamming function
to calculate the number of bits set to check for violation of
exclusivity.
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
With this change now individual drivers can use standard cable
names as below:
static const char *arizona_cable[] = {
extcon_cable_name[EXTCON_USB],
extcon_cable_name[EXTCON_USB_HOST],
"CUSTOM_CABLE"
NULL,
}
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
